3d printing filament splicer

In the security set, you get: - Long & short barricade walls - Corner and straight connectors - Turret connector bases - 3 different defence turrets - Alarm siren tower - Security camera tower - Burn plate with fuel module All the parts are...

I printed it with white PLA and have no problems after about 12 months, even though we had already nearly 40°C this summer. The holes have a diameter of 6 mm, so you can use M6 threaded rods. The length can be controlled by the number of levels.</p>...

__Update 20th May 2018__ Added a different, low profile pen holder, embedded in a fake cockpit: this is exclusively for aesthetics, and print as a single object, however it's also available on...

The case is designed to be printed with a layer height of 0.2 or 0.3mm. You can lower the height if you want more details which is recommended for the ARC reactor. Supports are needed on some parts.I used PLA on everything but the electrics carrier....

// FISH FEEDER MINI BY FAU // Caricato su mini fish feeder il 29 marzo 2020 durante la quarantena per Covid-19 // Versione definitiva e attiva // 1 sola attivazione giornaliera data dalla luminosità della lampada accesa o spenta // dopo 10 minuti...

... supportless.   Files are for personal, non-commerical use only. Please help support a small business and fellow gamer -- do not sell or distribute files or sell prints. Please see the STL Licensing Agreement for additional information. ...Thank you!

The entire box is designed such that if you print with 6 shells in your setting the outside walls will be solid, and the front wall will be double thick as it will take most of the hits. The bottom is flat, but has a large recess to allow you...

It is designed for easy printing and easy assembly. It is a decoration for a desk or as a relaxation lamp. The light bar uses the Arduino nano. ... You can load your chosen code into this chip, such as: rainbow, fire flames, and many more.</p>...

*** Edit 29JUN21 *** I added : -- A plate V2 : The fan duct outlet are 20 degres tilted instead of 30 degres in first version The holes that allow the tightening of the screws are lightly closed (approx 2 layers) so that the overhang print is...

I wanted to add lighting to my Kossel so I could monitor overnight prints without leaving lights on all night. The Neopixel range of addressable strips and rings seemed perfect, needing just a single data line for RGB control and a 5-volt supply. At...

I printed this with PLA on my prusa mini with supports on the build plate only, 40% infill, 4 perimeters. for the support settings I used: Z contact distance: 0.2mm pattern spacing: 3mm contact layers: 4 xy separation between an object and...

... in 1924, when 54,775 people attended an FA Cup third round game between Burnley and Huddersfield Town. [Wikipedia] You can request a full color printed model via email to SWIFTLANDREPLICAS@OUTLOOK.COM. ... Current price (2022) is $40 plus shipping.

This was printed on a Flashforge Guider II, High Quality, so the tolerances are good, but I also allowed a 1/4mm tolerance between parts and at this level of quality, it gave me a good fit. Painting it was using acrylic spray, primed and filled,...

I printed mine at a speed of 50, with a resolution of 0.2 mm. Assembly instructions below, assembly photo above. As always, any questions, don't hesitate to ask.Assembly:See numbered photo for reference.During assembly you'll want to keep an eye on...

There is a bonus version for those who can print multi-material with a Zelda Triforce design. While the two hooks on the sides do a great job of keeping the handheld secure, the hooks on the bottom and top needed slight tweeks. The hook on the bottom...

Initially named the RR Donnelley Building after the printing company that served as its primary tenant, it later became the corporate headquarters of United Airlines in 2007 following a deal that included acquiring naming rights to the building. This...

After clicking print, you'll be prompted to open the new tab and save the image or discard it, whichever you prefer. In order to proceed further, select each individual render starting from the deepest (-3900) layer all the way up until (-2900),...

## NEOPIXEL MOUNT For the mount, I quickly printed it out of PETG, pressed the NeoPixels in, and soldered them together. The warm board stick will into the mount, but to be extra safe I slathered the back with some hot glue. ## HOTEND WIRING ...

A new thicker-walled Ramps-FD box has also been created to help those who have trouble printing the original one. This is version 1 of my Ramps-FD enclosure, featuring a 30mm fan and an EEPROM hanger. I am upgrading my Duplicator i3 with Ramps-FD...

Unfortunately, all my individual printed part files are in 3mf, thus not uploadable here, so I had to bunch them together onto a few plates as stl files which are not really complete. There are a ton more parts (and many different versions of them)...

This brings me to this new part – it's essentially a clone of a design by Mangtronix http://www.thingiverse.com/thing:280974, but after printing his part I realized it wasn't long enough for the Wanhao Duplicator i3 (I didn't realize at the time...

This is my first attempt at sharing a 3-D printing model. History: A few years ago, after purchasing a CNC machine, I decided I would design a D-Handle that I could use for my Porter-Cable model 450 compact/trim router. I believe I came up ...

I calculated that the production didn't justify the cost of printing the 402 parts for the space rocket and made the decision to have them laser cut out of plexiglass. Then, I ordered all the straight parts (1HSP to 5HSP) to be cut out of plexiglass...

You cannot sell the digital model, a derivative or adaptation of the model, nor can you sell prints of the model. ... If you have any question, if you want to talk about the project, if you want to speak to other builders or if you are interested in new...

Note on pressure booster: The wings is only one wall thick so make sure to use "Print Thin Walls" in Cura. How to measure static pressure: https://www.thingiverse.com/thing:4401775 <h2>2020-12-10: Minor update</h2> Reinforcement at coupling...

2016/10/16 New: 2S Light Version Available for Printing Polycarbonate - a Game-Changer in the RC World! This is an exciting development that is only compatible with the previous version of 2S. 2016/10/06 New: 2S Version with Adaptation to Lipo Bold...

Except for the spacer ring, all parts are printed with ABS for stability and the possibility of stable gluing. The spacer ring is made of TPU. For adjusting the air gap between rotor and stator, the space rings are 1 or 2 mm high and can be...

I'll update this when my print finishes. The Fly can fly from any position to land on any bug that that your opponent placed, moved or flipped on their last turn. This includes bugs on top of a stack. It then moves one space down into an empty...

12mm tubes have been tested, and test prints are being done with PLA. The fitment of the connectors may not be the same with different plastic combinations. Ideas for improvement include using TS Twist Plug to stop any ports up that aren't being...

This battery holder has 2 vertical tabs intended to be soldered on a printed circuit. Here it will be necessary to fold them horizontally then solder the led respecting its polarity. To easily remove the battery, make a small hole in this holder,...