3d stl file

It doubles back at the far end to run parallel to itself on the other side of the bar. The switch clips have the small end inserted into the frame groove, and stay in place when rotated 90 degrees so they are upright as shown in the photos. Print...

If you have the proper filament colors, no painting is needed. The assembled model is 250mm tall. The model is in proportion to my other Wonderland models. Enjoy, and don't get lost while going down the rabbit hole of 3D printing! Print...

Probe: The probe is from the shaft of a faulty 30mm cooling fan from the hot end of my 3d Printer, superglued to a 5mmx2mm neodymium magnet. Alternatively use a 2mm ferrous metal wire cut to about a 10mm length. The other end is similar, but I...

It takes about a week of printing on two Prusa printers 24X7 to build this ship.The rocket thruster nozzle doesn’t take very long to print, though. Printed at .15 mmPrusament filamentCreated on TinkerCad.Enjoy!The second rocket nozzle has not...

every 3D print is slightly different an unique in surface quality, if you find a spot with a pointy, rough or elevated spot  use a a scalpel, sandpaper, etc to get rid of it for a smooth...

Note the c/sunk screws held in place behind the LED strip. Installed Lightbar, with heatshrink tubing added (Light intensity reduced to aid photo). How I Designed This Born of necessity... After acquiring the MMU unit, I've had to relocate the LED...

Arduino Nano is connected to wheel base via mini-Din 6 pin connector (SPI serial protocol), so no external power, drivers or USB connection to PC is needed. More info about HW and Arduino code is here...

## **Taille:** * **Longueur:** 57,34 mm * **Largeur:** 49,36 mm * **Épaisseur:** 3 mm ## **Conseils de fabrication:** * Pour encore plus de discrétion, imprimez le bouchon d’alarme à l'aide de filaments 3D de couleur noire ou grise. * La densité...

Print Settings: Printer Brand: Robo 3D Printer Model: R1 ABS + PLA Model Rafts: No Supports: No Resolution: 0.2mm Infill: 100% Notes: This design was intended to be printed without supports, assuming good bridging capabilities from your printer and...

This is a small missile I built for use with a sci fy model. Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

The 3D model in the pictures are from a Creality Ender 3 and have adapted the necessary dimensions for this project to my Creality Ender 3 pro. When removing the support, I always first pierced the edge between the support and the part with the...

BACKGROUND: I have posted several 3d-printed cases for standard 60% plates and PCBs, but have been neglecting the GK61. This case is an ode to the GK61, which possesses a couple of features that allow for the implementation of a gasket mount: (1) the...

Remove supports at the marked locations Remove the top bridge-layer marked with green, this is only there to enable the printing of the grid and will block airflow if not removed. BLTouch Front Mounted To fit the cover over the front mounted...

7.Use grease rather than oil to lubricate the 3D printed threads. You may need to use the Pivot Knob as a Tap the first time used to free\clear the thread. 8.On an Ender 3 V2 you may need a longer ribbon cable or cable extension to achieve the...

This mounts a Raspberry Pi 3B on the right side under the bed, which makes cable management a bit cleaner. Print the bottom part and one of the tops depending on whether you need a slot for the camera's ribbon cable or not. Also needed: 1x M4 T-nut...

It is mostly 3D printed, and just requires a couple of bearings and some nuts and bolts. It is quite strong enough to hold my camera (~ 1.6 Kg) and I wouldn't expect any problems, with decently robust printing up to 2 Kg at least.</p> <p>First, a...

Designed with SketchUp, fixed with Microsoft 3D Builder, sliced with Cura and printed in PLA on my Robo3D R1+ Parts: Some kind of power supply with a 5.5mm plug A 5.5mm socket (from AliExpress "5pcs/lot High Quality Socket Female Panel Mount...

... </strong></p> </p><div><p>May need to rotate pieces in slicer to enable the fastest print times. Add support where necessary, but shouldn't be necessary as long as parts are oriented properly on the build surface. Category: 3D Printing

Now I hope it works out for you as well as for me.Enjoy!P.S.: If you like this design and it maybe solved some of your problems, please consider leaving a small tip :)Print SettingsPrinter Brand:AnycubicPrinter:All-metal...

You should also share with your students some of the limitations of 3D printing - overhangs and bridging are obvious ones, but you should also talk about size limitations. I had two designs that were incredibly big and wouldn't fit at all. Rubric...

=&gt; Discarded Side View of Iteration 1 - notice that the measurements here are off by 0.4mm in Z and XZ! Itteration 2: Avoiding the M4 screw head on the other side seemed like a better idea, yet still the measurements were off Iteration 3 -...

So should work for noisy 5015 3D printer fans too. Check your airflow after fitting. Features: Short venturi / velocity stack cone inlet Modal barrier to break up resonance into 8 separate modes, thus reducing peak intensity of primary fan...

 Replaced corresponding Motor Plate as well.OverviewThis group of objects implements a CAN based Toolhead for the Voron 2.4r2 3D Printer.  The design uses a slightly modified version of Voron Clockworks 2 extruder in which a BTT SB2209 Toolhead PCB...

I do plan on redesigning this sometime in February or later as this was all done using Microsoft's 3D Builder and not CAD software. The gears are noisy and things need to be made with more precision but it works as well as beautifying some of the...

The next version will likely have longer front arms, a thinner and shorter middle section, and a removable gimbal mount for storage and travel (for my model of gimbal, Tarot T4-3D, but hopefully can be adapted for others of similar size). Printing...

With this customisable 3D printable design, you can turn any cup holder into a sturdy stand for your device! When was the last time you actually put a cup in a cup holder anyway? This fully customisable design can be adjusted for cup holders and...

Good bed adhesion required to prevent large parts lifting in corners. Post-Printing Full assembly in the video: https://youtu.be/Cv5pEcBI5HwrnrnHardware required:rnrn- SKR mainboard adaptor to printer: original M3 screwsx 4rn- SKR mainboard adaptor...

https://youtu.be/H-_2R-mKoMo Subscribe to find out more support free 4K Time-lapse video: Subscribe Now!http://www.youtube.com/iczfirz Addiction to 3D Printing? Watch these time-lapse! ... https://youtu.be/uNqqN5Ao_hI <a...

3D Printing and drone building and flying provide a fun way to learn about mathematics, science, and technology, and can also help people find a sense of community. Part of providing free access is to help young people and those in education by...

... with the cover if attached right-side-up)</p><p><strong>Example using pegs to hold cover with endstop attached to cover... Everything seems tight, so this might be the best way to go if you want everything to look stock,Category: 3D Printer Parts