3d touch ender 3 pro

Ender-3 Pro 3D touch sensor mount This is a remix from https://www.thingiverse.com/thing:3383611 Just added 3.5 mm to bring the sensor a bit closer to the bed.

Holder and adapter for P.I.N.D.A by Prusa for Ender 3 PRO instead of 3D Touch. ... You need: - M3x10 bolt - M3 square nut Firmware settings: #define NOZZLE_TO_PROBE_OFFSET { -44, -31, 0 }

... датчика авто-уровня BL Touch. ... Не мешающее не чему! Обновлено: 15.01.2022 * Мод под вплавляемые гайки (M3 X D5.0 X L4.0) https://aliexpress.ru/item/4000232858343.html * Усиленная версия крепления BL-Touch https://aliexpress.ru/item/32832887426.html

A remix of the [Mini Satsana + CR Touch](https://www.thingiverse.com/thing:5254926) file by [hobie2987](https://www.thingiverse.com/hobie2987). The original [Mini Satsana](https://www.thingiverse.com/thing:5160364) design had some wayward vertices...

**Description** ==================== This is a remix of TinyTouch NMPG, a very cost-efficent alternative to BLTouch and other commercial products - adapted for use on Ender 3/Ender 3 Pro with stock extruder assembly Please note that even though this...

I searched and tried a lot of brackets to fit my Ender 5 Pro but could not find any that fitted perfectly (Ender 3 brackets do not have the hole for de v-belt neither for the hole x-axis screw in the corner). There is already a 2,5mm spacer on the...

thanks and hope this helps anyone lol print it with many wall layers and then 100% infill would probs be strongest Adding offsets cuz I'm using it rn and it works for me: Ender 3 pro: X= -47, y= -5, z =-0.36 but irrelevant cuz you can just change...

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket. Category: 3D Printer Parts

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.

Remix of ebyaskawa Ender 3 Pro Umbilical Support Bracket. ...I only added bl touch mount to it.

this a direct drive for a ender 3 pro with cr touch ( that my first try off publish thing )

I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.

Petsfang Mount for CR Touch and Sonic Pad G Sensor ADXK345 for Ender 3 Pro using stock hotend plate

This direct drive conversion for ender 3 pro. pacifically designed for cr touch. ...I made this in tinkcad.

The bracket has been designed to accommodate a CR touch on an ender 3 pro with the Satsana 3d printed fan shroud. You should not need to print this with any supports, 3 or 4 walls should be fine. ...I ended up needing to adjust my Z offset to exactly...

mount for china BL touch for ender 3 pro print a paper glue to 1,5mm irn plate and mark holds and drill, cot plate

Add a touch screen interface for Klipper on your Ender 3 / Ender 3 Pro / Ender 3 V2 with a 4inch LCD touch screen + KlipperScreen. More information: https://youtu.be/jIFCERxnAXU https://www.youmaketech.com/ender3-touch-screen-interface-for-klipper/...

Comprei esse sensor:...

Remixed version of the Ender 3 Pro BLTouch Mount by puturai. mount that can be used for the CR-Touch from creality. works with the included screws but needs 2x M3 Nut. Nothing more to add than that it works well for me. ...This one needs some supports...

A more rigid version of the BL-Touch mount for the Ender 3 Pro Fang Duct. Printed with Tree Supports and high infill. Edit: After printing I noticed that the part is slighty to large. The side of the upper support tentacle touches the...

BLtouch mount for Ender 3 Pro Microswiss Direct Drive kit, offsets the BLT 60 degrees, enabling you to take the standard Ender shroud off without removing BLT.

The original works nice for bl-touch, but does not enough room for cr touch wiring. ...So, i made a ugly, quick, hacky cut to fit my needs. Printed in ABS, 30% infill, on a modded Ender 3 gen 1.

Slight modification to change the source step file to the bolt pattern for the x-carriage on the Ender 3 (validated on Creality model) and Ender 3 Pro.  Used as many bolts as possible to add stiffness. Using the same 7mm thickness from the BIQU...

I made an enclosure for my Ender 3 S1 Pro and wanted to put the controller outside for easy manual control... (I might build an Octoprint RPi enclosure with switching relays etc at some point as one larger unit integrating the touch control...). ...

It is processed to fit perfectly on stock Ender 3 Pro. Due to the fragile nature of the initially design of the BL Touch mount, it was remixed into more strong one.. Both turbine fans are wired into one socket to the board.. Optional printing...

I designed this simple 3d touch mount for ender 3. Reason why i designed it like this is becouse i have Red Squirrel Compact Fan Housing mod on my ender 3 pro and this is only way that i can come up with to mount leveling sensore. Also i think it...

(At least on the Ender 3 V2 with the Sprite Pro extruder) You would then set the endstop position to keep the nozzle zero above the build plate. The fit is good, you will need slightly longer M3 screws than the ones originally used to mount the...

-Place the assembly on the Ender 3/Pro and start both screws but don't tighten yet. -Press down firmly on the area below the LCD but just above the mounting screws so that the cut away on the back is held against the aluminum extrusion. -Then...

CR Touch offsets are : x_offset: -46.5 y_offset: 0 Hardware for CR-touch probe: 2x M3 nuts With KLIPPER You can modify the offset in the "printer.cfg" file: [bltouch] x_offset: -46,5 y_offset: 0 You may also need to adjust your mesh if you get an...

This is a remix changing the magnet orientation in order that the magnet is facing the Touch Mi.