5.25 to 3.5 3d models
2685232 3d models found related to 5.25 to 3.5.thingiverse
Drive bays from **5.25" to 3.5"**. Perfect fitting for Cooler Master Silencio 550, but it should be for other cases. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6no3Y02Rhw9
thingiverse
I needed to create put 3.5 drive into 5.25 slot. ...Made this small adapter.
thingiverse
An adapter so you can install 3.5" drives in 5.25" drive bays. You need two of them! Edit: New version uploaded. ...Old version was silly lol.
thingiverse
Adapts 3- 5.25 optical bays to 4- 3.5 drive bays. The cage allows for airflow and clean wiring. The curves are intended to provide rigidity. Each of the HDDs can be secured to the cage with screws. Nuts can be glued into the cage for mounting the fan...
thingiverse
PC case 5.25" to 3.5" adapter for floppy drive or card reader (Modecom in my case)
thingiverse
This is a basic but functional 5.25 to 3.5 inch hard disk adapter. Why make yet another one? - This one should be extra easy to print with the tear-drop holes - It can accept standard 6-32 hard drive screws that self tap into the holes. -...
thingiverse
While I was at it I added the SSD bottom screw holes to allow it to mount either. ... Depending on your cases screw holes, you might be able to stack 2 of these in 1 slot, but I found at least 1 case that it didn't, so you can check that on your own.
myminifactory
HDD support to place 3.5"HDDs on 5.25" spaces inside computer.Hope you enjoy.
thingiverse
HDD support to place 3.5"HDDs on 5.25" spaces inside computer. ... Hope you enjoy.
thingiverse
You want to use your 5.25" bay to hold 5x 3.5" HDD with clip holder, this thing is for YOU ! Forget the others and watch this, Bro ! Perfect HDD fit Perfect 5.25" bay fit Perfect clip holding Oh my god ! Love it ! Print it ! Enjoy it ! Hey !...
cults3d
You want to use your 5.25" bay to hold 5x 3.5" HDD with clip holder, this thing is for YOU ! Forget the others and watch this, Bro ! Perfect HDD fit Perfect 5.25" bay fit Perfect clip holding Oh my god ! Love it ! Print it ! Enjoy it ! Hey ! ...
thingiverse
I also have 3.5" to 2x and 3x 2.5" brackets in a similar design. The nuts can be pushed in with a pair of pliers and pushed out with a fine pair of tweezers using the bolt holes. The 3.5" drive standoffs requre M3x25 countersunk screws. ... I...
thingiverse
For mounting you will need at least four M4 screws and nuts and four screws that fits your HDD. ...It is designed to not need much material while still being sturdy.
thingiverse
... для установки жестких дисков в системный блок. ...Позволяет установить HDD либо SDD диски на полки системного блока 3,5 дюйма (под стандартные HDD) либо 5,25 дюйма (под дисководы). ...Главное преимущество - минимальная себестоимость и скорость печати!
thingiverse
Adapter for front panel of 3.5 "usb 3.0 to 5.25" bay of optical drive, off center for easy printing. 3D model different from the photos, corrected an error in the position of the holes Adaptador para montar un panel frontal de 3.5 (usb 3.0 o...
thingiverse
Easy and cheap Sata internal docking station - PC 5,25 to 3,5 Sata slot YOUR MB MUST SUPPORT HOTSWAP TO PLUG AND PLAY HDD I use this simple software (description):http://www.ghacks.net/2009/04/05/enable-sata-hot-swap/...
thingiverse
Heavily the original design to install a 3.5" floppy disk drive into my Compaq Portable II, may also work on other computers with those extra thin 5.25" bays. ... https://www.youtube.com/watch?v=Xm6NXmkQdVg
thingiverse
Combo adapter for mounting two drives (3.5" and USB floppy) in a single 5.25" bay. I took the USB floppy drive out of the case and mounted it on the adapter and connected it to an internal mainboard USB port. I edited the original thing:881057...
thingiverse
This is a 5.25 inch frame for 3.5 inch hard disk. You can add a 40mm fan for cooling the hard drive if you want. The outer side part is a silencer for the fan. It's a double "S" air duct that air enters from the sides and suppresses fan noice. ...You...
thingiverse
This is a redesign, i tried to make it work without glue, but not sure if it works for every plug or what is the better way in the end. ... though i think the 3,5" frame looks quite good and places the HDD inside your computer. ...
thingiverse
Converts a big drive bay to a small one using a spacer only one one side. ...The large holes are for screwdriver access to the inner screws.
pinshape
This is a 5.25" to 1x 3.5" and 1x 2.5" drive bay adapter. It is pictured with my previously designed 3.5" to 2x 2.5" bay adapter mounted in the 3.5" slot. Printed in PLA, with 20% infill, weighs only 83 grams. This model can accommodate both 7mm and...
thingiverse
This is a 5.25" to 1x 3.5" and 1x 2.5" drive bay adapter. It is pictured with my previously designed 3.5" to 2x 2.5" bay adapter mounted in the 3.5" slot. Printed in PLA, with 20% infill, weighs only 83 grams. This model can accommodate both 7mm and...
thingiverse
HDD Adapter fits in most computer cases used to place HDD/s in CD/DVD drive bays Included Solid works files made with solid works 2014
thingiverse
By design, the PC-Q08 has an SSD mount at the bottom of the 5.25" bay, so I just needed to model an adapter to fit 2 more 3.5" drives in it. I'm sure there are other cases that have empty space above or below the 5.25" bays, so I wanted to make...
cults3d
Mounting brackets for a 5x 5.25" bay. ...Made for https://www.thingiverse.com/thing:4106276
thingiverse
Mounting brackets for a 5x 5.25" bay. ...Made for https://www.thingiverse.com/thing:4106276
thingiverse
Needed a solid and easy to print 5.25 bay to 3.5 drive adapter, and couldn't find exactly what I was looking for anywhere on thingiverse, so made this one. For mounting the adapter to the bay, add 4x M3 threaded inserts. This relies on threaded...