6x9 camera 3d models
109593 3d models found related to 6x9 camera.prusaprinters
works wonders with any PETG in my experience.(as seen in the pictures) If you have any questions, feel free to drop into the filament and film discord, a discord that plays host to several camera designers, camera enthusiasts and printing...
thingiverse
test for a Ground glass film holder for an old Kodak Recomar 18 camera (6x9) Has not been printed yet, so not sure if it fits. Measurements taken from an old glass plate holder, using a cheap caliper. Test print looks pretty good, needed to adjust...
thingiverse
I wanted a 6x9 camera to shoot infrared film. I chose to build a fixed focus camera because I hardly shoot anything closer than infinity. Lens I used: Tominon 75mm f/4.5 Film holder: Lada for Plaubel Roll film back. Viewfinder:...
thingiverse
This is an optional cable-actuated shutter assembly for the terraPin 6X9 pinhole camera. This will only work on the 6X9 version of the 'slider' insert. A 3mm nut fits into the front plate to receive the tapered thread of the shutter cable release.
thingiverse
The terraPin 6X9 Pinhole Camera is unlike any other pinhole camera, 3D printed or otherwise. Developed after years of experience designing and constructing pinhole cameras, the terraPin is intended to be very easy to assemble, modify, and hack. ...
thingiverse
The 6x9 frame is centered both vertically and horizontally within the 4x5 camera's rear standard. Note that because the frame counter shows the 645 frames (not the 6x9 frames), you'll want to expose on frames 1, 3, 5, 7, 9, 11, 13, and 15 to avoid...
thingiverse
If you are interested in building more pinhole cameras, a roll of Gaffer tape is a great investment.) Camera Body The camera body is assembled with five other parts: -Shutter -Hexagonal pinhole plate -Shutter Key -Mounting ring -Top Frame The body of...
thingiverse
An adapter that lets you attach a Linhof 6x9 Roll film back to the Will travel 4x5 cameras by Morten Kolve https://www.thingiverse.com/mortenkolve/designs
thingiverse
The terraPin OSKAR Tuxedo 6X9 pinhole camera is easy to print and assemble, requiring but a single lock nut and bolt for the shutter and a flanged 1/4-20 nut for the tripod mount. The 29 mm 'focal length' provides for a wide angle (approx. 110...
thingiverse
Made a new insert to Durst Trineg negative holder to handle 6x9 format without the defalt glass. ...
thingiverse
Speaker adapter to put 6.5 inch speakers in 6x9 inch holes. Print one per speaker. ...Use 2 of the old holes and brace the third with this
cults3d
Funny enough I have seen several adapters for 6.5-inch speakers in 6x9 spaces, but not much in the way of 6x9 speaker spacers. I hope some of you find this useful! ... The OpenSCAD file is also included to customize this for your needs (for...
thingiverse
I have seen several adapters for 6.5-inch speakers in 6x9 spaces, but not much in the way of 6x9 speaker spacers. Use the customizer to make this whatever size you need. The OpenSCAD file is also included to customize this for your needs (for...
thingiverse
These were made to fit over 6x9 speakers that are surface mounted on plywood. Speaker sizes vary between brands, so make sure of your dimensions before printing. Best results on the cover were at 40% cubic infill, the ring at 20% standard infill. ...For...
thingiverse
2015 Ford F150 front speaker bracket for 6x9 speakers, probably will work with other models and years, but I've yet to test it on other trucks. ...Seal the bottom of the bracket before mounting if you want to, and drill a hole wherever you please for...
thingiverse
I recently tried to install new 6x9" speakers in a new vehicle that took 6x9's....I'm finding out some 6x9's are actually a little larger than the standard 6x9's. They were close to fitting, but not quite. I scanned the speaker cutout template,...
cults3d
Size is about same as 6x9, but can easily be seen as 7x10. With 3 holes to simulate bass under them. Designed to fit 1/24, but also 1/25, can be scaled. L= 29.9mm Depth = 15.95mm Height = 1.9mm *Measured on printed part, resin. For personal use,...
thingiverse
This is a hollow speaker box for a 6x9 car or marine speaker. Designed for Polk Audio DB691 6x9 3-way speaker. Should work for other models, just be sure dimensions are correct for hole spacing. Mounting holes are 170mm x 120mm apart, measure your...
thingiverse
Adapter from 6x9 inches to 165 mm speakers (specific size for the model AD W600NEO) Print Settings Printer Brand: Zortrax Printer: Zortrax M200 Rafts: Yes Supports: No Resolution: 0.19 Infill: High
thingiverse
......It should work in 03-08 rollas and with most 6x9 speakers but i think the screw holes in the driver are bit different than standard. If anyone needs different screw hole placement I can upload a blank file so you can edit it or drill your own holes.
thingiverse
Speaker adapter that serves for the front door of a Frontier / Navara (D40). I divided the piece into 2 pieces to be able to print on my A10M printer (220mm x 220mm). To install it was necessary to open the holes of the part a little more, but...
thingiverse
Designed to fit pioneer 6x9 speakers in rear of 93 Mitsubishi Bravo
thingiverse
It was cheaper for me to design and print adapters than buy some on Amazon/eBay, etc. ...This 6x9 design is common in Ford vehicles. I needed to mount some 5-1/2" speakers I obtained. ...This adapter is very sturdy and solid.
thingiverse
Stock Toyota speaker is 6x9 size, but the mounting points are different from aftermarket products. I designed a simple adapter to accomodate aftermarket speaker. ... Printed using ABS to withstand heat and vibration Infill used is 50% with >1mm wall...
thingiverse
Design for a 6x9 speaker for my Rzr roll bar. ... Mount design was remixed off of Teasleyprint's Tower / Roll Bar Speaker Can 6.5 The mount is a separate piece and various sides and you will find them at the link:...