Fan Mount used by Droodle for Cobblebot Mod 3d models

A custom-made cover mount for the Geeetech GT2560 controller board, specifically designed to accommodate a 70mm fan. The cover comes with a built-in standoff to secure the back side of the board. I used M3 threaded rods, which are essentially M3...

Simple mod of the excellent Duet Smart Effector cooling setup posted by GermanEngineer at https://www.thingiverse.com/thing:2909853 All I have done here is extend the 5015 part cooling fan mount vertically to account for the additional height of the...

This is a replacement fan mount for fatshark Dominator V2 for this thing: http://www.thingiverse.com/thing:1109091/#made Category: R/C Vehicles

Radial Fan (50x50x20) Mount and Duct for TEVO Tarantula Inspirations struck and I drew from the following source: https://www.thingiverse.com/thing:1403610 I made adjustments to make it work with a different model of radial fan.

Fan Mount for Solidoodle 4 with Stock Extruder This mount is designed to be easily removable and fits perfectly with the Apple MacBook fan, eliminating the need for a ducting solution. ...You can purchase this fan at...

Depending on your filter material, it might be beneficial to use some kind of high pressure fan, that is optimized for use in watercoolings / radiators (e.g. Arctic P12).The outer dimensions match the 120mm fan (120x120mm), the wall thickness is 3mm...

Instructions: Select from the following parameters to design a custom bracket for your project: Fan Spacing: Adjust the distance between the mounting holes on your fan to fit most common case configurations. PCB Width: Choose the width of the...

Introducing a custom-made 60mm Ducted Fan Mount for 40mm motors! Created using Blender and printed with Cura, this mount is designed to securely snap onto any Nema 17 or 40mm motor. For motors with larger pin sets, slight modifications may be needed...

Mount lets you put a nice fan duct right onto a Taz5 (or others).\nThe cooler duct is available here:http://www.thingiverse.com/thing:1025471\nThis mount adapts both the duct and the fan on the left-hand side, plus it gives you the extension pad for...

A Custom Double Radial Fan Mount Made for My Tevo Tarantula with a BL Touch Mount Note: This mount was designed specifically for my personal use only, so assume it may cause damage to your printer and potentially lead to a house fire if used. I'm...

Fan attaches to mount using screws that came with fan. stepperFanMountSingle - final version that only has 1 mounting point and can be used without issue on any stepper motor. stepperFanMount - original version, used in pairs with 2 mounting...

This mount is designed specifically for a motor that measures exactly 42.3 millimeters by 42.3 millimeters. Meanwhile, the attached fan has precise dimensions of 40 millimeters by 40 millimeters and stands at a height of 10.5 millimeters. The...

I had some leftover LED light strips from another project (16.4ft, 300 Units SMD 5050 LED Flexible Light Strip, 3000K Warm White) that I decided to use on wallyTHE gecko's fan mount. Unfortunately, my LED strip was only 10 mm wide, so I had to widen...

This modification is for series three kegerators from Keg King, but it may fit other series and brands that use a 60mm fan mounted to the inside wall of the fridge. The manufacturer's mounting method does not permit any useful airflow; instead, the...

A mounting apparatus for the hot end and cooling fan in a J-head assembly is available, ensuring stable positioning and optimal performance of these crucial components.

CoolDeck 40mm fan mount for Steam DeckPrint grille side down. ...No supports necessary.</p><p>I printed at .3 layer height.&nbsp;</p>

Simply secure your fan to the mount using matching M3 screws tailored to the size of your specific fan, and it effortlessly snaps into place within the machined grooves in the aluminum frame. ...If a tighter hold is required, you can insert a...

... frame, and you're done. I'm using the fan duct from mileshkin: https://www.thingiverse.com/thing:2706092 Update: 22.11.2019 The 20mm Fan Mod is now also available! ... Write tips, remarks, and suggestions in the comments, I'll try to answer them.

A maker built a mounting bracket for a 170mm fan, securing it to the side of their mini kossel using the very screws that keep the wire guard in place. ...When attaching the bracket to the printed part, caution must be taken as excessive force can...

I'm using a simple 40mm fan mount for my step-up converter (check out the picture) that powers the LED on this homemade 100W LED flashlight, the "EyeOfRa 215". ...I designed it with ease of printing in mind, avoiding steep slopes, bridges or overhangs.

A 60mm fan mount designed for Printrbot Classic's underside, created using Tinkercad, can be simply detached. The fit may initially be loose, but this can be fixed with a few layers of tape. Be cautious of the wiring as well. ...However, note that there...

To attach an 80mm fan on my Prusa printer's side for cooling purposes, I created a mounting kit comprising three parts: a frame rod clip, a slotted arm, and a fan frame. The design allows multiple tilt adjustments along various axes to accommodate...

the fan is a preassure fit so no screws needed, fits very tightly, the four holes in the corners are to be used for drilling holes through your enclosure to mount the filter box (work in progress) on the other side. there is also a hole for running...

Mount the Ultibots V3 fan duct to the non-belt side of Richrap's quick-fit carriage using M3 x 20 and M3 x 25 screws, along with two M3 .5 nuts. Print the part with a raft and support, then remove any leftover raft and support. Finally, fit it onto...

Here's My Part Cooling Fan Mount For My Bulldog XL Extruder. This Is Mounted On My Makerfarm Prusa I3V Printer. ...This Should Also Work For The Bulldog Lite Extruder As Well.

The ultimate fan duct for your remixed 3D printer mount! It's a game-changer, and the good news is that it's compatible with various E3D mounts. ...Plus, all tolerances are carefully calibrated for smooth printing performance.

I originally had the fan mod on my anet but wanted to add the light holder for easier view but there was no way to mount them together correctly. This design prints without supports. I printed at 10% infill and have had no problems with warping. ... ...

I designed a fan-mount to install my Noctua NF-A4x10 40mm fan on a Pi 4. You can use the original screws which came with the fan. The mount is screwed down with 3x35mm wood screws. Between the fan and the heatsink is a clearance of around 2mm. You...

I highly recommend using the Noctua ones. 4 x M3*16 bolts (or larger if you're using a thicker fan). 2 x M3*8 bolts. 4 x M3 nuts. 2 x M3 T-slot nuts. (Optional) A 40x40mm aluminium heatsink for enhanced cooling performance. If you have any ideas,...

The prototype of an enthusiast mount aims to shield the thermistor from windblast impact. ...Intended specifically for a solo-mounted eighty-millimeter fan positioned at arm's length away from the core assembly.