Large Spool Holder for Replicator 5th Generation 3d models

I got tired of reaching behind my printer to grab the spool holder, unscrew it, load a spool onto it, screw it back together and replace it so I designed this top-mount spool holder for my Nova Labs Prusa i3 (BG8). It should fit all versions of the...

... The main structural components include two customized SpoolDisc prints: one each for the top and bottom sections of the spool holder. Additionally, there is one key print named BracketKey to secure the filament spool in place within its housing.

Here is a rewritten version of the original text: Large Spool Guide Important Note: To keep my prints in pristine condition, I employ a clever trick - folding a small strip of duct tape over the spool's edge, securing it firmly in place and...

In theory your spool holder is ready but if you plan on using it without the rollers make sure the supports are stable and that the flanges of your spool are exactly parallel (they often are not !) otherwise you will risk a drop and to brake anything...

This spool holder is designed to replace the original one for Qidi Tech Xone-2 printers and can be left attached at all times. It's much more convenient than the standard holder that requires unscrewing every time filament needs to be changed. The...

For optimal functionality, the vertical risers must exceed printer clearance with spool height requirements set at 3 inches; my preference uses 6-inch risers for a sturdy foundation. Spools of any size can be accommodated on the horizontal top axle...

I remixed the original model to remove the grid and utilize a deeper cylinder in the center. ...This was at the request of my wife for her large brushes. ...I scaled the model 150% for printing.

The spool holder that comes with the powerspec duplicator i3 is just a straight rod mounted on a bracket. This was causing bad print results toward the end of the spool for me. This will mount on the same bracket but uses 2 608 bearings and...

A spool holder designed specifically for 2020 aluminum extrusion material. It accommodates spools with an inner diameter of about 55mm and a maximum width of up to 70mm. To enhance its structural integrity, we recommend inserting a piece of 5mm...

in english: This is a filament-spool-holder for the German RepRap NEO 3D-Printer. It is snapped in the backside of the printer an can take various sizes of spools. The screws I used are 6mm thick. Feel free to remix or improve this part. in german:...

Spool holders for m6 rods, with both dimension you may use them at nearly any Filament spool up to 1kg. Center hole must be at least 21mm and maximal 75mm. The rod may be fixed or loosed, just as you need it. Thread may fit a bit hard at the...

Spool holder for sample or small quantity filaments that are loose (not on a spool). Designed to fit into a 3" (I.D.) cardboard tube. This size of tube is very common (in the US)... most rolls of tape (packing tape, masking tape, blue painters tape)...

This is a replacement spool holder for the stock filament mount on an Ender 3v2 printer. Attaches with the stock nut. You will need 2 6003-2RS bearings (35x17x10). Threads are a bit tight, so after printing I lubricated with a bit of lanolin and...

in english: This is a filament-spool-holder for the German RepRap NEO 3D-Printer. It is snapped in the backside of the printer an can take various sizes of spools. The screws I used are 6mm thick. Feel free to remix or improve this part. in german:...

This is a spool holder specifically for the Creality Cr-10 and Creality CR-10s as it mounts to the top of the control box! You will need: 4 x Prints 4 x Skateboard bearings Superglue Simply print 4 of the same file, pop the bearings on with a bit...

This filament spool holder, printable with ABS or PLA on a MakerBot, demands solely printable components and PVC glue or epoxy. To assemble, affix the base to your MakerBot using an existing cap, then glue the stem's larger end into the bottom part's...

Replacement part for the totally unlikely event the spool holder is still inside an empty spool while it is thrown away... Print Settings Printer Brand: Anet Printer: A6 Rafts: No Supports: No Resolution: 300 Infill: 20 Filament: doesn't matter...

A custom spool holder mounts neatly on 2020 extrusion. Countless versions exist on Thingiverse, nearly all using 8mm rod and 608ZZ bearings. I opted for a design centered around 5mm rod and MR105ZZ bearings, which happened to be readily available. As...

The spool holder I cut and added a piece of plastic that fit perfectly to get more stabilization when gluing. Done with Tinkercad. Now I can use cheap 2.5kg spools even on my small printer! ... See the original post for instructions on how to fit:...

This 3-piece laser cutter design creates a low-friction spool holder for the Flashforge Creator Pro, taking just about four minutes to cut on my Glowforge laser cutter. Cut it out of six-millimeter acrylic sheet, using offcuts from Tap Plastics...

The Ender 3 V2 combined with the original spool holder tower did not fit in my IKEA STUVA enclosure. This custom mount enables the spool to be hung onto the inner wall of the enclosure. It was designed so that the black cylinder that came with the...

This is a replacement spool holder designed to fit the Vector 3 3D printer by Eaglemoss. It's been reinforced and lengthened to accommodate standard 1Kg filament spools. Print Settings: Printer: Vector 3 Rafts: Yes Supports: Yes Resolution:...

Here is a sturdy foundation to attach your Ender 3 Stock Spool Holder - simply snap into place using the t-nuts that come bundled with it.

Users are required to use a spool with a holder that accommodates AWG22 wire measuring 1.7 mm. ...The maximum allowable cable diameter is precisely 2 mm.

First Printer. ...First Design. First Print (other than tests). A simple spool holder to fix onto a 30mm extruded aluminium frame.

My spool holder brace broke, so I designed a new one in Fusion360 then I topology optimized it so it uses less material. 

Just print 2 pieces (WITHOUT mirroring). ...Insert from side of v-slot profile. Spool holder here: https://www.thingiverse.com/thing:2070272.

A DIY enthusiast has cleverly repurposed a standard 1kg Sigma spool holder to accommodate a trio of high-precision 608 bearings, maximizing storage capacity and efficiency.

The LulzBot Mini gets a major upgrade with the colorFabb Spool Holder, a sleek and sturdy accessory designed to make your 3D printing experience even more efficient.

When printing without utilizing the rear filament spool holder, simply secure the holes using the provided cup to prevent any damage or contamination.