Large Spool Holder for Replicator 5th Generation 3d models

... fitting 22 by 35 mm I used a stainless steel tube of 270 mm by 22 in diameter and I made stopper plugs. ... to prevent the tube from coming out of the holders . and for printing I used the holders in cura. ...and I added the IKEA logo on the holder.

This is an upgrade for the Adjustable Spool Holder for Original Prusa i3 MK3 ENCLOSURE. https://www.thingiverse.com/thing:2867521 I designed a new bearing/filament roller with a 608 bearing, as shown in the photos. The outside diameter of the 608...

I received my new Ender 3 V2, and I designed this spool holder (its a copy of CR-6 SE) I have some issues in the holes for screws. I draw 5.25mm diameter for holes, for M5 screw, but the printer make some littler. The bigger part, took me 6 hours,...

A simple yet ingenious spool holder designed specifically for the AnyCubic Kossel Plus. This innovative solution eliminates the need for any additional hardware, eliminating the hassle of screws and bearings altogether. Once printed, the two halves...

I printed this with 100% infill for maximum strength and 0.20 layer height. Installing The Spool Holder The filament spool holder is deigned to snap onto the plastic T shaped frame from the front side of the printer (please use the picture of the...

The design of the 45 degree spool holder proved to be refreshingly straightforward. This update aims to rectify the problem where new spools were winding up over the edge of the spool. It has the capability to accommodate spools as wide as 80 mm. ...

With this insight, I aimed to find a top-loading spool holder with a similar concept to replace the MPMD's handle but discovered that available options required extra hardware like ball bearings or wheel bearings, or needed to be printed on a larger...

A spool holder upgrade designed for larger spools, replacing the factory unit but not requiring the factory-provided nut. Print Settings Printer: Duplicator 6 Rafts: No Supports: Yes ...

Filament Spool Holder Base for BuzzBox Enclosure Kit Unveiled. This updated design accommodates a detachable filament holder and features a more slender width than its predecessors. The buzzbox enclosure now boasts an adaptable base to suit diverse...

This allows me to relocate the weight of the spool off the top frame of my printer and provides ample locations for mounting multiple spool holders above the printer. To assemble this setup, you'll need to print four ConduitSpoolRoller units per...

Adapter for different filament spool sizes Category: 3D Printer Accessories

Easy to use container for storing Filoprint PLA LITE filament spools.

Elevate 3D N2 Spool Support to 35cm for Weights Between 2.3 and 4.5 Kilograms.

Spool Stand For Ender 3 / v2 It can only Carry 1kg or lower filaments

Spool Mate for Ender3 v2Frictionless rotationAdjustable spool stopper with counterlockHanging systemSupports most spool sizesEase of printingDrawing dimensions of the hanging system (ender3v2 mount) provided to adapt to other supports or 3D printers...

To ensure uninterrupted printing, I took matters into my own hands and designed a custom spool holder that could accommodate the filaments I had originally bought online - 1kg spools of high-quality PLA from Hatchbox and AMZ3D, both boasting a...

Rosewill Dehydrator RHFD-15001 combined with Horizontal Spool Holder featuring 608zz bearings and DIY Filament Dryer / Dehydrator, Tweaked v2.0. An improvement was made by adding a centering pin and locking cone from another successful spool holder...

There are three variants of the part included: standard (spans 4 honey comb elements in x-direction) rotated (spans 3 honey comb elements in y-direction) single covers only one honey comb element Please be aware that the Gravity Spool Holder the...

The guide is designed for use with Mendel Max printers that employ aluminum extrusions on their top horizontal frame, and it works alongside the 3DBotic simple filament spool holder found at Thingiverse. To install, print the part, attach it to the...

I modified the existing spool bearing component by changing its center hole to a rectangle, allowing it to fit securely on the above mentioned spool holder. Additionally, I added a small U-shaped piece to hold the spool and bearing in place,...

I couldn't find the exact design I wanted, so I modeled up this simple design for a top mounted spool holder. This is intended to work with a direct drive setup, works for Ender 3 and Ender 3 V2. No bearings using in this design, intended to use M5...

I designed this Spool Holder specifically for my TEVO Michelangelo. It's similar to that thing on Thingiverse: https://www.thingiverse.com/thing:2832449, but I came up with two separate parts to make printing without support material a lot easier.

These two parts form the fix for the spool holder of the Eryone ER-20 series of 3D printers on which the threads were made too close to the edge. All explanations in the ER-20 presentation video, here: https://youtu.be/DYbYvvYdh1c I also put the...

I'm re-engineering my previous spool holder design for Bowden.\nIt still relies on 4 x 608zz bearings with clips and a threaded rod acting as an axle for the bearings, and has been incredibly helpful so far - it's been able to feed non-stop up until...

Spool Holder for 1-Inch Extrusion October 10, 2019 - Introduced 20mm wide version October 23, 2019 - Revised to use a Radius on top October 30, 2019 - Made further improvements by splitting the design into two parts, eliminating the need for...

Replacement Migwire Spool Holder for Lincoln PowerMig 180C. This item was designed with Tinkercad. Edit it online at https://www.tinkercad.com/things/bD1WcAJ1T3X Print Settings: Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: Doesn't...

This is an adapter to mount the [UNIVERSAL FILAMENT SPOOL HOLDER](https://www.thingiverse.com/thing:4855918) to Voron (2) frame. You would need 2 M5x10 bolts and inserts for the actual mounting. I designed it to go on the side, where the perspex...

This is a versatile Filament Spool Holder designed specifically for the TEVO Black Widow, but its utility extends far beyond that. Intended to be securely attached to the top of an 8020 aluminum extrusion, it can also be easily adapted for use with...

A sleek and streamlined spool holder perfect for Anycubic's Kossel Plus. No extra hardware is necessary, no screws, no bearings - just print it out! Once assembled, clip the two halves together with the cylindrical core in place, securing it firmly...

Upgraded Sidemount Spool Holder for Ender 3 Pro I required an 8mm diameter rod to serve as the axis, along with some 22mm x 8mm x 7mm bearings that are commonly used in skates and rollers. The Lego system is more efficient in this regard. *Side...