Link for heroscape 3d models

The surface acts as a bridge between the 1-dimensional link and the 3-dimensional space it lives in.The torus links and their Seifert surfaces live most naturally in the 3-sphere, a higher dimensional version of the more familiar sphere. We transfer...

This slotted waveguide antenna, designed for tp-link WR703N WiFi travel routers, features a pie-segment radiation pattern (120 degrees horizontally, narrower vertically) and requires no router modifications. Made from 3mm plywood, it assembles...

This is the replacement part for the red link at both ends of the Bond Bridge of the famous TIZIO desk lamp, created by Richard Sapper for Artemide in 1972. With time, the plastic of the red links tends to crystallize and come apart (see photos). ...

The tray is 1.6mm narrower and the ears are 0.4mm narrower.Low center of gravity, 4-link servo mount for the Emax ES08MAII and ES08MDII in the SCX24.It pushes the servo back 2.5mm and down 2mm compared to most servo mounts. The servo actually sits on...

ABS is more flexible. This is a Z-Axis Chain Link for JGAurora A5s (Possible other Printers). This is re-mixed from the chain (OLD LINK ONLY) The New-Link is not Re-Mix https://www.thingiverse.com/thing:3954315 That I Modified for my use. I got tired...

ALL PROCEEDS WILL BE GOING TO BUYNG 3D PRINTERS FOR LOCAL SCHOOL DISTRICT Low profile Cuban link bracelet design with functional clip. The sizing in the STLis small so scale the model until the X axis is your wrist size. With a tape measure or a...

To install this link on a standard bicycle frame for belt drive conversion (for example, the Gates Carbon Drive), you will need to choose between two hard soldering options: one for M6 countersunk screws and another for M8 flathead screws. Both are...

The mounting bracket for the left-hand side, which houses the power supply jack, is referred to as "Halter links." Meanwhile, "Halter rechts" denotes the right-hand side. Be cautious when dealing with the screws, as they have a tendency to break. The...

I think link chains as mechanical parts are a really interesting option for things like height adjustable desks etc. since the chains are really cheap and highly available in home improvement stores. They also can take high loads, however they are...

Extension Link for Surgical Mask Strap Saver Based on Quinn Design We've created an innovative extension that provides a simple solution to prevent ear discomfort and strain when wearing surgical masks with elastic straps. Inspired by the Quinn...

Printer Settings for D-Link DSC-5222 are Optimized with a 20° Incline.\nPrint Settings\nPrinter Brand is Zortrax, a Leader in the Field.\nPrinter Model: Zortrax M200, Built for High-Quality Prints.\nRaft Support: Yes, Essential for Smooth First...

I attached a camera mount for my D-Link DCS-932L IP camera to the Raise N1 3D printer's top bezel. The part securely screws into place, giving me a clear view of my prints at all times. I redesigned the original component using Tinkercad's intuitive...

A simple snap in clip to hold cables inside the long_link_12 part

1U rack mount to attach TP Link TL-SG1024D. ...You can mount this onto 2020 extrusion

TP-Link's Compact UH700 USB Hub Dock Keeps Your Workspace Organized

However, I had issues constantly with the link cover tabs snapping off either while trying to snap them in place, or breaking as the chain flexed. I tried using both PLA and ABS with the same results (at 20% infill). I simply added a little bit...

This is a wall mount for TP-Link's TL-WR902AC travel wifi router with two (2) M3 countersunk screw holes for mounting with M3 wood screws or anything M3-size and countersunk. I use these routers as cheap Wifi extenders and Wifi-to-LAN adapters for...

4 perimeters of 0.4 width), again, for increased rigidity and to make better use of the ribbing I designed.These fit a bit tight, similar to the plastic Ryobi Link hooks, so they should be pretty secure. I used PLA because it's what I had, but of...

Stand for vertical installation of a TP-link router or switch with side dimensions of 101 × 25 mm. It has an air passage at the bottom and does not cover the ventilation windows in the device. From the back there is a holder for attaching the...

The stand's design allows for airflow through the TL-SG105E, ensuring it stays cool and functions properly. A custom label can be printed in any color you want, then glued onto the stand for a personalized touch. ... If you're using an OC200 with your...

A DIY Mount for Your D-Link Webcam that Tracks Z Axis Motion The setup is pretty straightforward, involving attachment of a gantry mechanism that syncs up with the build plate's Z axis movement. With careful planning, the webcam gets amazingly close...

This is a wall mount for the TP-Link TL-WR841N that eliminates drilling entirely. Six m3x10 mm screws are required, with holes slightly smaller than 3mm in diameter to ensure secure attachment. Additionally, I have designed the mount to conceal cable...

I have been prowling the internet for TINY quick links for my rockets. the normal smallest is 3.5mm and its just too large and way to heavy for a typical 3" rocket. I did find some 2mm quick links but its a Japanese specialty item and almost $5 EACH...

I remixed Sundownnn's 4-link servo mount https://www.thingiverse.com/thing:4549464 after trying to use it with my Emax ES08MA II servo. There simply wasn't enough space. It is 0.9mm wider (0.8mm + 0.1mm for possible print inaccuracy). The Emax servo...

Since I dislike pegboards, I picked up this gate kit from Home Depot (https://www.homedepot.com/p/YARDGARD-6-ft-W-x-4-ft-H-Galvanized-Metal-Adjustable-Single-Walk-Through-Chain-Link-Fence-Gate-3283AD48/203432021). I've also included a file for the...

This is a encasing for the link cable adapter by Agtbaskara. The adapter can be found at https://github.com/agtbaskara/game-boy-pico-link-board.It is based on the following assembly:1) Pico H (e.g. https://www.pi-shop.ch/raspberry-pi-pico-h)2)...

You want to avoid buildup of bacteria. I used superglue to glue the two parts together.  WeVibe, if you don't like this existing, please add a variety of sizes of links to the toy's packaging (and send me one) and I'll happily take...

... also fit seamlessly. To print this innovative accessory, use the following settings: Print at a layer height of 0.1-0.2mm No support material is required Use an infill density of 15-20% A raft provides optimal adhesion for the best possible results

I built a mount for my D-LINK model: DCS-8525LH Home Wifi Pan-Tilt-Zoom camera that lets me choose between using the four holes at the top to attach the supplied camera mount either upright or inverted. Alternatively, I can use it without the camera...

Lever-operated mechanism in Luger NAVY pistols, referred to as the rear toggle link, facilitates reliable and smooth functioning of the weapon's action.