Makerbot Replicator 2x Filament Fan Upgrade 3d models

... with non-uniform filaments, I increased the size of the output hole in the design. ...This modification can even accommodate filament from Makerbot, which is not always perfectly uniform. ...Check it out at http://www.thingiverse.com/thing:52203/.

This adapter snaps into place on a 5th gen makerbot replicator to allow filament spools with Ø2"ID X 2-1/4" width through hole (KP3 Creality ENder 3 Pro CR-10S ???) Great deal for filament on ebay, wanted to mount it in the filament tray, not on the...

Secure a 55mm heatsink/fan on the Replicator 2/2x Y-stepper motor with this clip, providing ample clearance for moving parts. The fan used is http://www.amazon.com/gp/product/B006Z4J8JE; any equivalent heat sink/fan combo should work. Print with ABS...

The smart extruder's filament guide failed and we replaced it with Wurstnase's Modified Threaded Filament Dust Filter, an enhanced version specifically designed for the Replicator 5th Gen, which offers reduced support thanks to its flat bottom. ...Our...

The MakerBot Replicator 2 can experience issues with filament spooling, but you can solve these problems by adapting the design from bluejay117. This enhanced version ensures smoother feeding by increasing overhang and adding a stop inside the feed...

The Thing serves to direct the thread from the reel onto the MakerBot Replicator 2's tube, resolving an issue whereby the filament from a fully wound spool may leap over the spool's edge and coil around the axle. ...An update has since been...

A vital accessory for Replicator 2X is a user-installable filament guide that blocks jams, ensuring your entire hot end remains intact and operational. ...The quick snap installation process involves merely inserting it directly into the standard tube,...

Our MakerBot Replicator 2X's Y-axis rail-guide snapped, so we designed a STURDIER replacement. We were able to print two new parts since we have multiple printers. You'll also need to remove the gears and reinstall them in the new part, which...

1kg MakerBot filament spool holder for 5th Generation MakerBots by admg consultancy This will work on the 5th Generation Replicator, the Z18 and the Mini. It allows use of MakerBot 1kg filament spools, while retaining the captured filament guide...

This modification should be compatible with any Replicator 2x clone, including CTC, PowerSpec, FlashForge, and more. REV_1.0: Change: Duct thinned, fan moved back Result: Air flow was not as good as the original design but better than the first...

This filament tube guide snaps into the existing guides that damage the filament tubes over time and allow them to fall out. Print instructionsCategory: 3D Printer Parts Instructions See gallery for suggest print orientation.

Filament tubes take a beating as existing guides continually snap into place, eventually allowing the tubes to slip out and come to harm. ... Instructions Suggest a suitable print orientation in the accompanying image gallery to get started.

This all started with a remake of the Makerbot Replicator Mini Spool Holder: http://www.thingiverse.com/thing:751182 Print Settings: Printer Brand: MakerBot Printer: MakerBot Replicator Mini+ Rafts: Yes Supports: Yes Resolution: 0.20 Infill: 20%...

This Threaded Filament Dust Filter, designed by http://www.thingiverse.com/thing:153807, has been improved in a remix (http://www.thingiverse.com/thing:258598) with a wider knurl for added functionality. However, I require a smaller version, so I...

This also work perfectly to this type of printers: Flashforge Creator Pro, Flashforge Dreamer, Flashforge Inventor, Flashforge Creator Wood edition, Dremel 3D20, Makerbot Replicator 2x, QIDI Tech 1, QIDI Tech Xpro, CTC Bizer, Anycubic 4Max, and other...

The exhaust is designed for the rear left corner hole of the MakerBot Replicator 2X, but you can use it as a side vent if you put the feet in a different direction when attaching the inlet to the fan. You just need to buy the non-printed parts, and...

Human: 3x filament guide. ...2x: Thingiverse #2173952 1x: Thingiverse #2130148 Print Settings Printer: CTC Bizer Dual Rafts: Anything Works Supports: Nothing Needed Resolution: 0.2mm Fine Detail Infill: Solid at 20% Density

I will mount a Raspberry Pi Zero W and Pi Camera to the front inside corner of the Makerbot Replicator 2/2X. My goal is to see if print is complete, and remotely monitor the print. The idea behind this project was inspired by...

3x filament guide. 2x: http://www.thingiverse.com/thing:2173952 1x: http://www.thingiverse.com/thing:2130148 Print Settings Printer: CTC Bizer Dual Rafts: Doesn't MatterSupports: Doesn't Matter Resolution: 0,2Infill: 20% Category: 3D Printer...

I designed a fantastic cooling fan that can be mounted without any additional hardware or supports. It simply snaps into the base where the extruders ride on, and its hole pattern is specifically designed for a 40x40mm fan. I successfully installed a...

This is a counterpart to https://www.thingiverse.com/thing:4064197, featuring a duct for a 6048 blower-style cooling fan mounted on the left side of the extruder carriage and pointing down, roughly in line with the heat blocks. It's designed to be...

Specifically crafted to accommodate a third 40mm fan for superior active cooling. I deliberately designed this print specifically to distribute airflow evenly around the printed object. Formerly, air solely emanating from the front wasn't yielding...

A system designed to thwart 3D printing comes to a halt upon encountering a slight dip in tangled filament rolls, resulting in a temporary pause in the printing process.

This tilted adapter has 4 benefits: The Noctua fan is REALLY quiet and reliable, making it a great upgrade choice. You should definitely consider upgrading. The fan is pumping cooler air instead of warm air from the bed as it's tilted upwards,...

Full Noctua cover has advantage of hiding the entire fan and also allows mounting the fan via rubber pads which are squished together, making the fan quieter. Front fan cover is just there for aesthetics and there are 2 versions - the round and the...

;) Full Noctua cover has advantage of hiding the entire fan and also allows mounting the fan via rubber pads which are squished together, making the fan quieter. Front fan cover is just there for aesthetics and there are 2 versions - the round and...

In my recent Replicator 2 maintenance process, I found myself disassembling and reassembling the extruder assembly multiple times. The spacers kept rolling off the platform edge, making it difficult to poke the screw through the fan without missing...

This part is a door handle and latch designed to fit flush with the 2X style printers featuring metal frames and routed plastic (foamed PVC) panels. It attaches to a hole in a lasercut 3mm Acrylic panel, as seen on Thingiverse at...

The x-axis alignment fixture holds the left pulley's axle firmly in place on the exterior of the left block, securing it during operation. To ensure stability, this fixture must be installed whenever wear threatens to compromise the mounting brackets...

These are high-performance silicone molds designed to provide heavy-duty protection for a hotend insulation system, I'll post detailed images once the silicone hardens completely. ...To remove air pockets from the mold, try using a sterile acupuncture...