Radiation Weather shield for Netatmo outdoor sensor 3d models

All of them work so you can decide, which one you like best. V1: Since the wind gauge is sensitive to UV radiation, I wanted to design the mount in a way that protects the gauge. V2: Same as V1 but with added drain holes on the bottom.V3: A...

Slim case for the Sonoff SNZB-02 ZigBee temperature and humidity sensor. This holder helps you to easily access the sensor without sticking it directly to the wall. Install the case with a screw or double sided tape and slide the sensor in. ... ...

... the horizon. ...This updated device serves as a long-term substitute for the initial toilet paper tube and duct tape setup I devised. The printed component fits over the lens cap of the sensor without needing screws, adhesive or tape for installation.

Netatmo Smart Video Doorbell (mount + cover for wires)The doorbell requires the wires coming straight from the wall into the case. If the wires are on the surface on the wall, e. g. ...if the doorbell is displaced, then this mount can be helpful.In my...

This is a simple wall mount for Netatmo modules that is inspired by https://www.thingiverse.com/thing:2160603. It has a minimalist design and can be attached to the wall using Tesa Powerstrips "SMALL". The Powerstrip can either be fully covered by...

I was in need of a holder for my Netatmo gear, which is equipped to monitor wind and rain conditions. Unfortunately, the diameter of the pole on my balcony measured only 25mm, making it incompatible with the original design. To address this issue, I...

This mount helps if you have to mount your sensor on top of something, as the original mounts are designed for walls and edges. ... If you have the new sensor (with only one screw on the backside), please use the hue_motion_pocket_small.stl as this is...

... I replaced the original PIR-sensor plate with a sleek and simple new one featuring an hc-sr501 PIR. Control over switching it on or off is now seamlessly managed by a Sonoff Basic module, programmed to follow a Tasmota rule for sunset timing.

Printed upright with NO infill, NO support and a single perimeter with a 0.35-0.4mm nozzle and around 0.15mm layer height.\nEnjoy.\nPrint Settings\nPrinter: boudloBot BB-01\nRafts: No\nSupports: No\nResolution: I had good results at 0.15mm\nInfill:...

Slim case for the Sonoff SNZB-02 ZigBee temperature and humidity sensor. This holder helps you to easily access the sensor without sticking it directly to the wall. Install the case with a screw or double sided tape and slide the sensor in. There are...

Remix of Delphius_JD's (https://www.thingiverse.com/thing:2821217) sensor box featuring a blend of cutting-edge components: WeMos D1 Mini, a compact yet powerful microcontroller TEMT6000 Light Sensor, precise illumination detection AM312 PIR Motion...

It is convenient that it allows you to remove the sensor without dismantling the entire case, on the latches, which is convenient when the device is hanging outside the window at a height. Special thanks for the help in creating and developing -...

Redesigned https://www.thingiverse.com/thing:4731693 to allow easy access to the sensor. The back part can be glued with adhesive. Please print the front part on the roof and the back on the bottom as in the attached images to avoid supports. ... ...

The original project by Micromet has been expanded upon.

This is a versatile enclosure designed specifically for use with a D1 Mini microcontroller and the SHT30 sensor module, allowing users to easily capture temperature and humidity readings.

Radiation Ring for Cisco Gold Ring Take the main ring from Cisco :)Rescaling chart of his ring and also the plate:size 3- 87 %size 3,5 - 90%size 4 -92%size 4,5 -95%size 5 -97%size 5,5 - 100%size 6 - 103%size 6,5 - 105,6%size 7 - 108%size 7,5 -...

Radiation Ring for Cisco Gold Ring Take the main ring from Cisco :)Rescaling chart of his ring and also the plate:size 3- 87 %size 3,5 - 90%size 4 -92%size 4,5 -95%size 5 -97%size 5,5 - 100%size 6 - 103%size 6,5 - 105,6%size 7 - 108%size 7,5 -...

:P:P You'll need to flip the stl so that it's face down, and use support on the build face to brace the recessed area where the Netatmo mounting block sits when fitted. The holes in the recess are simply markers for the fixing screw centres. File...

Other than that, it's a straightforward swap for the previous design, and requires the dry-lining box to be modified in the same way as the first. Refer back to that one, and everything will become clear. ... I'm finally happy with how it looks, and I...

Here is a remix from this article https://mavicpilots.com/threads/mavic-front-vision-warning-during-flight-300-feet-up-in-sun.1593/\r\n\r\nI, like many others, am experiencing issues with the Mavic halting mid-air flight due to direct sunlight.\r\nSo...

Sinalcos design + holes for screws since I dont wanna use tape outside.

The cap can be screwed into the ceiling using one 3.5mm countersunk screw, allowing for adjustment in desired direction. Next, insert the main body into the cap, securing further with a tie-wrap or small nut/bolt through the through-hole if needed. ...A...

This is an updated version of Thing 3029737 from thingiverse.com, with the logo removed from the front panel for a sleeker appearance, and strategically placed screw holes added to securely fasten it to various surfaces such as wood or walls.

__________ I filmed the room with an IR camera and i was shocked how many IR radiation comes from those intakes.... so i made those cover to block those radiations No need to drill or destroy the cover. ...you just need 8 small screws (like 4x2.5mm) ...

Thank you very much for the modification of enlarging and 45 degree design for better fits to the principal of weather metering and smoother 3D printing. With turning on slicer engine cura's experimental option called "enable bridge setting", I...

Wall Mount for Netatmo Outdoor Sensor - Easy Installation Guaranteed! Install your Netatmo Outdoor Sensor in minutes using our reliable wall mount system. Simply attach it with one or two screws, and you're good to go! ...The ideal spacing between the...

If it melts, I'll simply swap it out for ABS. To assemble this contraption, you'll need five 5x370mm cable ties or less, two M3x30 screws with nuts, and one 1/4" screw. ... Don't forget to position the Wind Gauge facing south, not north, if you're...

If that happens, I can always swap it out for one made from ABS. To assemble the bracket, you'll need five 5x370mm cable ties or fewer, two M3x30 screws with nuts, and a single 1/4" screw. ... Don't forget to point the wind gauge southward, not north,...

With Netatmo's rain gauge, you'll enjoy: Real-time precipitation data for informed decision-making Accurate measurements for precise analysis Enhanced insights into local weather patterns Upgrade to the latest in rainfall monitoring with Netatmo's...

Protective Mount for Outdoor Sensor of Netatmo Station - Wall-Mounted Secure Installation Solution