Solarbotics L298 Compact Motor Driver Mounting Plate 3d models

I needed a safe way to mount those modules, so i came up with these little mounts, modules should fit inside the edge perfectly and component feet should fit in the indentation. Mount the modules using M3 screws by directly screwing into the hole,...

I rapidly crafted this design to install an ON/OFF switch on the side of the AM8 frame or any 2040 extrusion. ...The switch's mounting hole has a 20mm diameter. Do you require additional information? ...Please leave a comment.

needed a mounting box for my garage to run some network for Fibre box. Hardware store closed and i needed to mod it anyway to take a round conduit on the corner. ... So did it all in one.

This is the mounting bracket for creality sprite pro extruder. I needed it to adapt to my ender 6. ... Dimensions may not be perfect but it was good enough for mine.

This device mounts humbucker pickups directly into a guitar body, eliminating the need for frames. ...Designed specifically for EMG 81 and 85 models, it can also accommodate other pickups suitable for Les Paul-style guitars.

You will need to print two tabs for this design. They can be found at: https://www.thingiverse.com/thing:3401942 or https://www.prusaprinters.org/prints/8512-din-rail-mounting-tab The module can be found at:...

The small stabilizer piece is to make it so there is less flex on the front plate when inserting and taking out the usb cables in the front. It should line up with a screwhole on the middle bar. I print this with the small piece with the hold on...

Designed for the Printrite/Colido DIY enthusiast, this plate empowers users to easily install an MKx type heating bed, boasting a clean finish and precision engineering. The center holes are perfectly aligned to fit the printer's original belt...

This is a custom plate designed for the heated bed Mosfet MKS V1.0. Its primary purpose is to prevent accidental electrical connections on the underside of the PCB. To secure it in place, M3 screws and nuts are used, with nylon spacers (11mm)...

... design. ... They can be found at: https://www.thingiverse.com/thing:3401942 or https://www.prusaprinters.org/prints/8512-din-rail-mounting-tab The module can be found at: https://www.amazon.com/dp/B0B1HNS9L2?psc=1&ref=ppx_yo2ov_dt_b_product_details

I designed this mount to securely attach the remote that comes with my Lutron P-PKG1W-WH Caseta Wireless 600-watt/150-watt Multi-Location In-Wall Dimmer with Pico Remote Control Kit, or alternatively, my Lutron LZL-4B-WH-L01 Connected Bulb Remote. A...

I bought a Bow Mount Minn Mota trolling motor to mount on my Lund 1436 Jon Boat. These are two simple bits to secure the rear most portion of the motors plate. The two forward screws get through bolted 1/4-20 through the front rail. The back left...

If you want to fix your multisensor to a carport or gardenhouse you can use this simple plate to fix it. (The inner hole for the sensor is about 2mm wider than the sensor itself. If you ever have to remove your sensor i.e. for battery replacement,...

I wanted to connect my [Coronado PST](https://www.astroshop.eu/solar-telescopes/coronado-st-40-400-pst-personal-solar-telescope-ota/p,10316) to an [one-armed Dobsonian...

Found building an ATX power supply unit mount to be challenging, as numerous designs were impractical for their screw positions and components. Built one according to the ATX specifications and conducted some testing on a few available power...

The small stabilizer piece is to make it so there is less flex on the front plate when inserting and taking out the usb cables in the front. It should line up with a screwhole on the middle bar. I print this with the small piece with the hold on the...

This mount replaces a computer monitor on a human-scale arm, designed for attachment to a quick release. It's made of two parts so either can be replaced if necessary (created for a friend's business with many arms). Someone else might need this...

Needed to build an ATX PSU mount and had a lot of trouble finding a usable model for the screw positions and other elements. Made one based on the ATX specs and a bit of testing on a couple PSU's I have handy. It might not work without tweaking for...

The holder has slots under extruder mount bolts and an additional one at the back. Print it out, test-fit LEDs (6 at back, 3 each side), possibly trimming dovetails near wires. Soldering wires within the holder can be tricky but necessary for four...

I had the OSN MX600 tripod laying around but the mount piece had been lost, so I chose to model a new piece as I really liked the tripod. I figured I would upload it in case anyone else wants or need a replacement. The hole is not threaded so the...

I mounted this print as a baseplate for my Sonicmodell AR-Wing 900. The Matek F405-Wing flight controller fits perfectly, secured with double-sided foam tape. To keep the baseplate in place within the aircraft, I applied double-sided tape at the...

... This is a remix of the supplied 3D model to mount the cube in a box (http://smartpid.com/wiki/doku.php?id=demo_tutorials) but the recessed text is setup for multicolor print. ...Print instructionsI have attached the 3mf file ready for MMU printing

This mount is specifically designed for the Reolink B800 bullet camera, but its concept can be adapted to any camera that requires a sturdy mounting system on thin or soft sheet metal. The mount features three pillars to accommodate the (Reolink)...

Designed this block set to be able to securely mount my Garmin Fish Finder/GPS to the dash of my 2012 CanAm Commander. the Dash features a hump in the middle that I wanted to straddle. Version in pictures is the first edition, with no holes that...

This mount allows the Aeotec Wall Mote Quad to have a right-angle USB connection plugged in while it is attached to the wall. I designed this because it was inconvenient to have to charge the remote so often. It can be screwed into a wall, or you...

... This is a remix of the supplied 3D model to mount the cube in a box (http://smartpid.com/wiki/doku.php?id=demo_tutorials) but the recessed text is setup for multicolor print. Print instructionsI have attached the 3mf file ready for MMU printing

This adaptable ball socket design can be tailored to fit snugly onto any ball fitting, providing a flat mounting surface to securely attach objects using double-sided tape, adhesive, and other fastening methods. Specifically, the STL file included...

There are slots on either side that go under the extruder mount bolts and one in the back if you want to add another nut and bolt.InstructionsPrint it. Test fit the LEDs. It's made to hold 6 at the back and 3 on either side. You may want to trim a...

Arduino Montagerahmen für L298 Motortreiberplatine Print Settings Printer Brand: Anycubic Printer: Photon Resolution: 0,2mm Infill: 20% Filament: Anycubic PLA red Category: 3D Printing

... ...Two designs are available: a single-piece version that demands additional support, and a two-part model requiring assembly using cyanoacrylate adhesive. This motor plate is designed for use with motors featuring 25mm center-to-center bolt spacing.