abs won t stick to bed 3d models

there is A "folding screen" design for big size or useing ABS ... ...(low warp) u know. Instructions there is A "folding screen" design for big size or useing ABS ... ...(low warp) u know.

I won't quit

Vase designed to be difficult to tip over just like the old Weeble Wobble toys. ...My print was at  25% just to cut down on time.

http://www.thingiverse.com/apps/customizer/run?thing_id=46335 Instructions Using the following options: SD_gap = 2 USB_sticks = 6 Device_Order = 1 build_plate_manual_y = 100 build_plate_manual_x = 100 Sign_FONT = orbitron Pencil_radius = 4 Sign_TYPE...

This was made from a video concerned with working with a surface that "fill offset" will not thicken it in FreeCAD. ... See video here: [to be updated]

This is what my computer had before it stopped letting me save. ...I have the rest on my comuter but don’t know how to save the file becuase it keeps giving me an error message every time I try to save.

http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Text = WON height = [9.5,7.7,8.8] Loop_font = Chewy Rotation = 0 spacing = [23.2,23.2,22] twist = -1 Loop_position = 14 Loop_character = u...

http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Text = WON Loop_position = 14 twist = -1 Loop_font = Chewy height = [10,7.6,8.8,7] Loop_character = u center = 21 spacing = [20,20,20] Font_name...

http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Loop_position = 14 Text = WON Loop_font = Chewy height = [9.5,7.7,8.8] Font_name = Luckiest Guy spacing = [23.2,23.2,22] Loop_character = u twist...

http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: spacing = [16.5,16.5,15] Loop_position = 10 height = [10,7.5,8.8] Text = won Loop_font = Chewy Rotation = 0 center = 20 Loop_character = u twist...

Pet food scoop that won't snap in half. ...It's volume is 68cm^3, or just over 1/4 of a cup.

If you 3d print a wiffle ball and hit it super hard it breaks but this one won't you can impress anyone. ...Use supports on build plate only.Made by Samuel Rea

When wringing needs to occur the handle is pulled up the shaft of the mop until it reaches the top stop the shaft of the wringer then start to screw the strings around each other and wring out the water similar to how one would wring the water out of...

All it has to support is the curl of the 3 dispenser chutes.Hints on gluing the side cover.You can use the dispenser without the Side Cover, but it adds strength and keeps the batteries from falling out.Be very careful when gluing the Side Cover to...

An inspirational plaque to keep building, keep exploring, and keep learning. ...The future we want is being built by you and I.

SummaryAn inspirational plaque to keep building, keep exploring, and keep learning. The future we want is being built by you and I.InstructionsGo heavier on the shells with a very light infill. Print with the ears down. I had 2 extra shells with 5%...

Made these solid bed spacers in ABS instead of using silicone or springs so I could lock the bed down and not have to keep levelling it after every few prints. Dimension's (3 18mm x 16mm) and (1 16mm x 16mm), With 5mm holes in the centre. ... Can...

A print that will test your bed adhesion. ... Varied heights starting at 0.20mm incrementing by 0.20mm/ Try to reduce curling on the tips of the stars. ...

( ͡°_ʖｰ)～☆

I needed a keycap puller that won't scratch my keycaps so I 3D modelled one that resembles the popular one with metal wires.You need to print two pullers and insert them into the holder. ...They have holes so you can stick a piece of filament into them...

This version of the battery holder for the Mobula7 quadcopter has two retaining ridges so it won't fall out of the frame and get lost or move when installing batteries. Also has a weight reducing slot on all 4 sides for added coolness. Print from...

Couldn't find one so made one up, enjoy! ... See more builds and Props: https://www.youtube.com/c/Props3D/ Sign is by my wife, check it out: https://www.etsy.com/ca/listing/644595906/just-five-more-minutes-nerdy-wood-sign Follow my prop...

Couldn't find one so made one up, enjoy! ... See more builds and Props: https://www.youtube.com/c/Props3D/ Sign is by my wife, check it out: https://www.etsy.com/ca/listing/644595906/just-five-more-minutes-nerdy-wood-sign Follow my prop development...

... to the bracket with two nuts. At both sides a dice slides over the shaft and is secured with a self-locking nut. Make sure the dice rotate freely. The shaft for the stop button is M3. Good practice: Drill all the holes to their intended dimension.

... in a way that they will not break along the layer lines when deflected. The simple solution is to split the model into separate pieces that can all be oriented in the direction that makes them easy to print but also maximizes their strength.

... for the stop button is M3. Good practice: Drill all the holes to their intended dimension.https://youtu.be/QFgmIKAay1g With three rotating elements it should not be too difficult to build a one armed bandit.http://www.thingiverse.com/thing:2131803

A couple of searches showed I was not the only person to have a problem with this particular manufacturer. See the attached PDF file for complete instructions. In my case it was actually a pretty simple fix. I hope this helps someone keep...

I edited the file using TinkerCAD to make it 80 x 80 x 5mm, and also created one with holes for fasteners if you prefer. ... Without holes (shown): https://www.tinkercad.com/things/dQR437EjfXb-the-future-wont-invent-itself-wall-plaque/edit With...

I edited the file using TinkerCAD to make it 80 x 80 x 5mm, and also created one with holes for fasteners if you prefer. ... Without holes (shown): https://www.tinkercad.com/things/dQR437EjfXb-the-future-wont-invent-itself-wall-plaque/edit With...

for the video so u can do the same thing