action figure 3d print

Sliced with PrusaSlicer, this design tests your printer's ability to print thin words without any layers on any side, showcasing its "floating" capability. Dimensions of the design: The base plate is 16 millimeters by 51 millimeters by one...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: - Short term tool storage for tools being used on an active project - Organization to help keep the bench cleaner - To help facilitate rapid tool...

I would love to see what it is being used for! If you like this thing, have as aswell a look at: https://www.thingiverse.com/thing:3239814 everything that this thing can do can be done as well with the newer thing. But it has a lot more options and...

The pieces I made to hold the bumper buttons haven't been printed or tested by me yet as I used hot glue in an earlier prototype piece. You can use just hot glue to hold them, but this may risk pushing them loose. The contact rings on the SparkFun...

#Installation instruction: ##Hardware: Print, sand, use some hot glue to attach the screen to the shell and to glue them together. ##Software: Requirements: none for standalone version www + php server - in my case Lighttpd + PHP on Raspberry Pi 3+...

Our design is nested and compact, which means it takes less time to print one set. The board we use makes wiring and assembly more accessible. With an internal battery charging circuit, you don't need to remove the battery for charging. To control...

So here we are about three months later with something that, after quite a bit of brainstorming, parts printing, carbon cutouts, messes and success stories, looks ready to be shared with the community. And now, it's over? Well not...

... or it can create a cone effect not allowing you to close the top. a little extra force may be required to pop the surround into the topBase. Commercial replication and production prohibited, selling files or prints without my consent is prohibited.

The pieces can be assembled in multiple different ways.  - Alien Desert bases: 19 different bases ranging from 30mm to 80mm, and including a desert rock scenery piece.  All the parts are pre-supported for SLA resin printing! Storyline of the...

Assembly Once all the pieces are printed, start by running the wire through the hole in the center disc of the inner_reel so that equal lengths are protruding on either side. Thread the wires through the holes in the upper_half so that the wire on...

Print with supports, 3-4 shells, 10-15% infill (unless you want it to be dense). Post-Processing, I took a Dremel and cleaned out the grooves. I lightly sanded the front and back, to smooth out where the supports were. I then painted it, followed by...

You'll need to print two of these, but don't worry about mirroring since this is symmetrical and so is the gap it fits into. You will need to upscale this object by 12.7 times or with an X, Y, Z of 101.6mm x 31.74mm x 10.38mm. With this scaling,...

Load capacity certainly is an issue worth considering, but it usually depends more on the quality of the wall than on the aluminum or printed parts. However, as usual I have to state the following: This is a hobbyist's work provided to hobbyists -...

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

It is the low-poly and easy to print version of ionic, doric and corinthian columns. Doric and corinthian columns are supportless, only ionic column has some easy to clean supports. Just like chess knight is not photorealistic and just symbolic, goal...

For this team project i worked with Joanna Su (link) Problem Statement: With a partner, you will design a “2D” placard using Solidworks.  You and your partner will have the same design which meets the constraints below, and you will EACH use...

From the original from HeroMe Gen 5 collection (https://www.thingiverse.com/thing:4460970) you will need to print: a. V6 retaining collar b. V6 air dam c. 4010-Lightweight Duct *FORWARD* d. Fan guard if you want... The mounting plate is used to...

Hilt Base (Rebel Crest design) parts list A) V4 RJ Hilt base lower hilt shelf (part 1 of 7) B) V4 RJ Hilt base lower shelf hilt cup (part 2 of 7) C) V4 RJ Hilt base back plate (part 3 of 7) D) V4 RJ Hilt base back plate screw cover medallion (part 4...

Thin "windows" are designed into the forward and bottom surfaces of the backpack, which can be cut away after printing to increase much-needed airflow. PRO-TIP: The DTX03 ships in standard-definition mode, but it's capable of recording nicer video...

It does not produce a valid three-dimensional object that can be printed. ## tl;dr: * `trunk();` * F6 (render) * Export as an SVG in OpenSCAD: `File > Export > Export as SVG` ## Thanks All Bezier Functions based on the excellent work of...

This transformation enables my DaVinci to print PLA at 80mm/s with impressive accuracy and minimal noise, eliminating the screeching sounds associated with fast movements. Travel speed has increased to 200mm/s. This mod necessitates that Repetier...

You are more than welcome to try and print this, but I made no attempt to make the objects properly manifold. ...Aaron Ciuffo (Txoof) Reach me at google mail: aaron dot ciuffo https://www.thingiverse.com/txoof/about released under GPL V3.0 Latest...

If your job isn’t the kindest, print this out and keep it with you, there’s always a worse job, like trying to live and work on this thing in the middle of a violent fast moving, constantly moving, lightning flashing orange and black sand storm you...

FederationDN-V2-ship-stls.zip – Print-ready combined ship STL files. This kit supports the following variant ship classes: Federation class dreadnought The original TOS-era three-nacelle dreadnought from Franz Joseph’s 1975 Starfleet Technical...

I aimed to keep the list of printed parts minimal by developing a two-gear system instead of a more complex scissor extension arm. A unique feature of my design is the guide wheel that supports the tracing gear to keep it level and prevents it from...

I use this as a wireless monitor for framing a shot. But there are some killer features of a DSLR I wanted to have on my phone when filming. So I made this Camera Rig and I slip my iPhone into on days I'm filming.  Print...

... compared with the normal version (+/- 2.5h less), a perfect solution for those who want only the TS100. SMALLER_xxx.stl's are not compatible with non-smaller versions, print one or another but do not mix them Timelapse: https://youtu.be/p505Rq6WJHY

Fill with 1" of water or enough to reach halfway up the micro-trays, place trays in water and allow them to soak for 5-10 min depending on how compact the soil is and how much root mass is present.\r\n\r\nMicro-trays can be washed in the dishwasher...

There is a bonus version for those who can print multi-material with a Zelda Triforce design. While the two hooks on the sides do a great job of keeping the handheld secure, the hooks on the bottom and top needed slight tweeks. The hook on the bottom...

...Both parts are easy to print without support structures. For reinforcement, the part to which the pool pipe is attached with screw clamps has a reinforcement. The hole in the container is approx. 45 mm and was actually drilled for the rubber sleeve.