adafruit 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

On the single phase motor models there's contactors and timers in there for the auto tapping function... if fitted. I wired the 12 volt psu's mains connection to the main switch of the mill, this is after the main fuse so it's protected by that,...

Link below --- Build history Years ago, duno, I made the bigger first case desgin, roughly modeled after the original. 2021 -the 2.nd design of a modified, more streamlined versatile case was made. -modified the pcb layout -new pcb was made...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

It can print without support, and if you have the workflow dialed in, it takes only about 30min per label from start to finish. You might get away with printing just the modell without the support stuff…. didn't try. Depending on your bridging it...

New version available: Please check out the new Ultra Flat Filamentholder model, now updated to be 8mm lower, more accurate, and faster printing :)\nFeatures of the Flat Filament Spool Holder\nJune 6th - Finally finished making it. Enjoy...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

I simply used a couple of dabs of model car glue, but you can use epoxy if you prefer. I would avoid CA because the fumes may fog up the inside of the lens. The finished part is shown in "modified camera.jpg." I just checked Amazon and found that I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

It will not fit a full sized stepper, use their model if you have the original stepper motor. I suggest printing with the end that hooks over the carriage on the bed with supports on bed only. There are minimal supports this way and the hook keeps...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Safety Information Please be aware that this product contains small items and is not suitable for young children.This product is a scale model and is intended for use by adults and children age 14+.Take care during use as some products may...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

... satellite. The team’s website is http://csdc.uvic.ca/ Note that I did not create the Diamagnetic Payload Assembly, this was created by A.G.O. Environmental Electronics Ltd. The magnetorquers are not in the model, as they are still in development.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 custom_corner_resolution = 8 stencil_drawing =...

This model is for a “streetlight-style” wired garden/pathway light. Brighten up your garden path with lights, without spending a fortune on MoonRays or similar products where a single lamp can cost up to $20! In bulk I can make these for about $3-5 a...

First, I had to model the front of the display to accommodate the RepRap Discount Full Graphics Smart Controller and then I also decided it needed a back to protect the circuit board. Done... Then I decided to tackle the problem of mounting a...

It has been almost three months in the making, and several bits are an additional 100–200 sketches beyond the base model, which means there is a ton of Mf-detail, I probably overdid it. My goal was to create something special for kitbashing,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

Just make sure to get the alignment correct before letting the glue set up!Notes:Raft:              YesSupports:    NoI've had the best luck printing these using a single-layer raft, with the part oriented...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

Finally, if your printer's bed is larger than mine and can accommodate the full required width of the inserts, you can merge the included additional bodies Body30, Body67, Body68, and Body69 with the corresponding model parts. The weight of each...

the tabs are at different positions on each model. * Group Token Holder - slots in behind the main card holder. * Player Holder - holds the large Agent Pawns. * Player Tray Base x 4 - print these in the 4 player colors. * Player Tray Top x 4 -...

If you're experiencing high stringing, do not worry, give it a blast with a heat gun, then a quick brush with a nylon brush and wipe down with a cloth to get rid of any remaining strings. Exterior Perimeters settingsTo ensure the best results...

This helps with the strength of the threads as it will be printed length wise on the build placeThis gives more freedom to place pieces in any orientation, as well as add spacers between larger parts for more accents and individualityFixed stringing...

If you like & use my models please consider supporting my efforts with the button below. Thank you!…Please be sure to hit like & post a make, I'd love to see your prints!The Vortex series grows with Gemini! Print faster with crisper cleaner looking...