adafruit 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_size = 40 stencil_shape = 4 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

This is a 1:50 scale model (metric) of a space rocket that transforms into a Mars base. (well, conceptually) Instead of building vehicles to transport pieces to build a base, it seemed more reasonable to use the whole spaceship as the future...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

This is resistant to everyday wear and tear, but we got warned that rust stains are not completely removable.So a stainless clothes drying rack became necessary.Most commercial ones just have powder-coated steel tubes which rust after some...

Infill doesn't matter because the model is a hollow shape. The filament must be elastic and reasonably heat-resistant. I have tried this in NinjaFlex which seems to work well. Anything much harder than Shore 85A is likely to be too stiff to act as a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Previous model description: I hooked up a 1400mah battery and drove this home from my local park around 500-600 meters with no heat issues affecting the PLA print. I have used this around the house quite a bit with the camera, and it works well. The...

It's just a model I whipped up, and sliced it with a bunch of retraction changes. Then went back and spliced all the g-codes together. Base Cura profiles I use: layer height - 0.2mm Optimize wall print order (do not retract before outer wall), print...

Already renowned for their authentic sound, Casio's latest model takes it to the next level with its impossibly small footprint. Measuring 43 percent smaller than previous generation Privia instruments, the PX S1000 is literally half the size of...

See Latest Updates Below ----------------------------------- * The latest model now appears at the top due to rearranged pictures. I wanted a unique look for my 4x Santa figure, if that's feasible... Took various elements from multiple 4x...

The models in my pictures were printed in beige ABS, which is a standard 1.75 mm filament from XYZ manufacturer. I have not tested other filament materials with this design. If printing as a fake sprinkler, I would recommend choosing black; bright...

Perfect for storing jewelry, electronic parts, cables, Lego models, tools, and other small items, the Pyramid Stacker offers a practical solution for keeping your belongings organized and within reach. By stacking the layers, you can store smaller...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

I made a slight modification to the model by changing the profile of the USB input so the bridge was less than 5mm (was almost 10mm) and changed the way the board mounts so the top has all socket heads and no washers (just an aesthetic thing). <a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

(I have included a model with logo, and one without)Assembly Instructions:Print the box and two clipsInsert bowtie shaped post on clip in to corresponding hole on box, then rotate until the push-clip lines up with the hole.Push the push-clip in to...

Print Settings: - Printer Brand: MakerBot - Printer Model: MakerBot Replicator 2X - Rafts: No - Supports: Yes Important Print Note: The key thing to keep in mind when printing these wheels is to use support material, especially for filling in the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 48...

Larger or smaller screws can be used if you scale the model appropriately, such as M3x8 screws at 150% part scale. Note that buying in bulk from a specialist supplier is significantly cheaper per screw. There are two versions of the container: the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

I am now only weeks away from getting my own printer :) but in my preparations, i found, that i had used an inaccurate BTT filament sensor model, in my design. It was pointed out to me that i never mentioned, which panel thickness i planned...

Tools Hex wrench 2mm and Mmm...

Before you merge them, DUPLICATE the logo "hole" model (Ctrl D) do not use copy paste it will "shift" duplicate will keep it where it is. Now shift select the body and merge to make your hole cut. You will note you still have the duplicate hole. Now...

Being in the United States, getting replacement parts for British model locomotives can be challenging, un-environmental, or impossible. but I found that the Bachmann Percy chassis shares a similar wheelbase to the 0-4-0's, and the Bachmann Duck...

*Note: don't order a GearVR with a white body - it is a 2015 model with smaller lenses that don't fit.* **UPDATES** **V3.3** (slight comfort improvements over v3.2). [print 1 for each eye] **Added a version for the prescription inserts from VR Lens...

Larger or smaller screws can be used if you scale the model accordingly e.g. M3x8 screws at 150% part scale. Note: it's cheaper per screw if you buy in bulk from a specialist supplier. There are two versions of the container available, the standard...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Cursed Immortality Season 2 - (2/4) The Umbratouched - Curse of Vengeance   Description Save money on this complete December Bundle, The Umbratouched, Curse of Vengeance, which contains all the models from the December release! These models come...