adimlab gantry 3d models

A sleek new front plate for the electronics box of the Adimlab Gantry takes shape, boasting two 4010 fan mount points strategically placed at the front. This design cleverly utilizes the four stock mounting screws and nuts to securely fasten the new...

I didn't change that much, I really liked the design and the things I changed were mainly just to make this work on the Adimlab Gantry-S printer. The main thing I remixed was to add mount holes for the Adimlab Gantry-S. I also changed the tension...

I barely changed anything, I truly loved the design and the things I altered were mainly just to make this work on the Adimlab Gantry-S printer. The main thing I remixed was adding mount holes for the Adimlab Gantry-S. I also swapped out the tension...

This direct drive mount attaches to the stock X carriage of the Adimlab Gantry-S (may also fit other Adimlab printers) and allows the use of either Phaetus dragon or Slice engineering Mosquito hotends with either Sherpa mini, Orbiter 1.5, or Orbiter...

This mod is designed for the Adimlab Gantry Y axis linear rail system. Part requirements include two MGN12-450 units plus an MGN12H. The user must print a linear rail support as shown and a mirror image of it. Eight M3-6 countersunk screws are...

This is a remix of "ADIMLab Z-Axis End Stop Adjustment" by Rabbit1210 to adapt it for the Adimlab Gantry-S 3D printer. Remove the factory bracket and the z stop from the bracket. For the knob, you will need an M3 x 40 screw, one M3 nut, one washer,...

This mod is designed specifically for use with Adimlab Gantry X carriages and linear rails. The stock sheet metal bracket, however, leaves much to be desired in terms of stability on the XY plane and weight reduction. To address these issues, a new...

This is a remix of "ADIMLab Z-Axis End Stop Adjustment" by Rabbit1210 on Thingiverse to adapt it for the Adimlab Gantry-S 3D printer. Remove the factory bracket and the z stop from the bracket. For the knob, you will need an M3 x 40 screw, one M3...

This is a remix of "ADIMLab Z-Axis End Stop Adjustment" by Rabbit1210 to adapt it for the Adimlab Gantry-S 3D printer. Remove the factory bracket and the z stop from the bracket. For the knob, you will need an M3 x 40 screw, one M3 nut, one washer,...

Print Settings Printer: Adimlab Gantry Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 80% or higher Filament: AmazonBasics PETG Notes: Printed using high density supports (touching build plate only). This will support the recessed hole...

Print Settings Printer: Adimlab Gantry Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 80% or higher Filament: AmazonBasics PETG Notes: Printed using high density supports (touching build plate only). This will support the recessed hole...

This mod is designed specifically for Adimlab Grantry part coolers that utilize a ring type configuration. To achieve optimal results, it's essential to use a 5015 fan. For more information and testing details, please refer to the article at...

The things I did change were to make this work on the Gantry, but it ended up being more than that. As it turns out, I had to change more than I thought, but kept the essential design intact. Mainly to how this thing is mounted and the clearance...

The things I did change were to make this work on the Gantry-S As it turns out I had to change a bit more than I thought but kept the essential design. Mainly to how this thing is mounted and the clearance needed on the end of the 4020 extrusion.</p>...

The things I did change were to make this work on the Gantry-S As it turns out I had to change a bit more than I thought but kept the essential design. Mainly to how this thing is mounted and the clearance needed on the end of the 4020 extrusion. To...

I tweaked the design to match 95% of the original blueprint, making key adjustments to accommodate a broader gap between the clamp's moving parts, incorporating smooth rounded edges, and enlarging the hexagonal recesses to snugly fit M3 and M4 nuts...

I designed one last year but lost the original file on Thingiverse, so I measured the one I had already printed and made some minor adjustments. The sensor attaches directly to the drag chain bracket. ...You might need to lengthen the sensor wires to...

Designed specifically to fit the Original Gantry Adimlab, this setup demands a dual fan modification and an additional hotend cooling shroud for optimal performance.

This file is designed for Adimlab's 3D printer, a 310x310 Z linear rail MGN12 setup with a 500mm long track and MGN12H carriage block intended to replace the existing rollers on the z-axis. Additionally, the motor attachment plate has been...

This is customized to fit the base of the Gantry-S. I used the smallest size from the source thing and they fit well. Here are the sizes, base sides 199mm, Y axis rail split into 4 pieces of 181.5mm each, front left 144mm and front right 110mm. ...Print...

Based off Garrett Waltrip's idea posted on the Adimlab Facebook group, you can use this to have a quick disconnect of the e3d hotend and also mount the gold mk8 extruder that's a popular upgrade for these printers. I've included the filament guide...

These covers are tailored specifically for the base of my Gantry-S printer. I opted for the smallest size available and was pleased to find they fit perfectly. Here are the dimensions: the base sides measure 199mm, the Y-axis rail is split into four...

I finally complete my first part cooling mod for the Gantry Pro. This is a side-mounted option with full x, y, and z adjustability. I modify a Cobra Head (https://www.thingiverse.com/thing:3738758) and a Volcano Head...

This mod is designed specifically for Adimlab Grantry printers that utilize a single motor to move the Z axis leadscrew. This modification addresses potential tramming issues you might encounter with this printer, eliminating irregularities on the Z...

This is a remix of the "ADIMLab Z-Axis End Stop Adjustment" by Rabbit1210, with the goal of making adjustment easier and the parts more robust. A couple of gears and a turn wheel replace the original adjustment knob. The gears and knob come from...

I made a slight remix to make it height-adjustable, and I used it on my Adimlab Gantry with an E3D v6 hotend. ... Tinkercad link: https://www.tinkercad.com/things/7dTHienanYc

This mod is a reworked version of my earlier design for Adimlab Gantry X linear rail carriage bracket with MK8 Extruder. I have revised the attachment to address the issues stemming from part warping caused by heat buildup. ...The redesigned carriage...

Made it for the Adimlab Gantry but should work on an 20x20 extruded Aluminum frame. Raise the Z axis high enough to slide this tool in. Turn off motors / printer. By hand, Adjust the Z axis down to rest on the tool by turning the threaded...

This adds versatility previously unheard of for the Adimlab Gantry-S printer.I recommend using the Hero Me Gen 6 system found here: https://www.printables.com/model/39322-hero-me-gen6-master-suiteI suggest using the Hero Me configured for an Ender 3...

By using a Creality x carriage the Adimlab Gantry-S hot end assembly can be easily modified to different hot ends or extruder configurations. This adds versatility previously unheard of for the Adimlab Gantry-S printer. I recommend using the...