airwolf hd2x 3d printer

... Layers. I connected the extruder fan directly to 12V source to avoyd the extruder carriage deform due to extra heat in case the slicing software stops the fan on first couple layers. Printer I used: https://www.thingiverse.com/thing:182675

Replacement XY Blocks and Belt tensioners for the AirWolf HD2x 3D printer. I have included the 123d files for your modification (non commercial). Left block bearing cap is modified to hit the endstop switch if you are running an aftermarket print...

helpful information about changes you have to make:http://www.soliforum.com/topic/12034/upgrading-your-airwolf-hdx-hd2x-hotend-to-e3d-v6-volcano/https://www.thingiverse.com/thing:956219 YOU WILL NEED: screws: hotend: m3x20 - 1pc m3x40 - 2pcs m3x25 -...

Fully designed in another program but I picked some measurements from: http://www.thingiverse.com/thing:1533860 Print Settings Printer Brand: Airwolf 3D Printer: AW3D HD Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 80-95 Notes: For best...

Fully designed in another program but I picked some measurements from: http://www.thingiverse.com/thing:1533860Print SettingsPrinter Brand: Airwolf 3DPrinter: AW3D HDRafts: Doesn't MatterSupports: NoResolution: 0.2Infill: 80-95Notes: For best effect...

this is my own design for a chimera with volcano hotends for the airwolf printer there is an included back plate that you can use to attach something to as I did in the picture You can print this without supports, the parts cooling fan is a standard...

this is my own design for a chimera with volcano hotends for the airwolf printer there is an included back plate that you can use to attach something to as I did in the picture You can print this without supports, the parts cooling fan is a standard...

This is a model of the Airwolf Axiom 3D printer 

This is a clamp on mount to use put the E3D Titan extruder on your airwolf printer if you have any of the printers build on the frame shown in the picture it should work Now you can use one of the best extruders made on your airwolf printer and...

Works perfectly on my HDX but it should also work on the HD2X. Print with a brim for more stability, I used 20 brim lines. Enjoy! ... When designing and testing this my computer turned off so if you want it in a step file leave a comment and I will...

This is a mount for mounting a AccuRemote 0-16" Electronic Digital Indicator Gauge on an Airwolf HD2x. http://www.amazon.com/dp/B0071SKHAW/ref=wl_it_dp_o_pC_S_ttl?_encoding=UTF8&colid=JNX19TKHE7P3&coliid=IUIQDXO5JX2QN This cheap little gauge lets...

I inherited(read "Found sitting unused in a corner of the storage room") an Airwolf 3D HD2x printer from work, and set about cleaning it up and making it useful. After replacing the hotend and updating the firmware, I started levelling the bed and...

... mounting.</p> <h3>Instructions</h3> <p>Designed to be printed at 100% infill without supports. I used ABS, PLA would also work well. Spacer keeps screw from protruding and interfering with spool. Choose left or right side Category: 3D Printer Parts

Replaces holders that ship with printer. Uses factory hardware for mounting. Instructions Designed to be printed at 100% infill without supports. I used ABS, PLA would also work well. Spacer keeps...

Ring light mount for AirWolf 3D printer. ...should also work with others that have a 50mm hole spacing for the Budaschnozzle.

Ring light mount for AirWolf 3D printer. should also work with others that have a 50mm hole spacing for the Budaschnozzle. Instructions What you will need besides this file: A Buda type hot end with...

This is to replace the upper right front corner on your Airwolf HD2X. They no longer make or support these printers, so if yours breaks, your out of luck, until now. ...I took the time to create these to keep my printer alive!!

STEP BY STEP INSTRUCTIONS HERE: http://www.soliforum.com/topic/12034/upgrading-your-airwolf-hdx-hd2x-hotend-to-e3d-v6-volcano/ The original hotend for the Airwolf HD2x is underpowed and you can't control each nozzle temperature separately. With this...

... parts, zip ties to enhance the clipping on the bearings, and one 6-32 x 1 1/2" screw to use for the level adjuster in the back. ...Print Settings Printer Brand: Airwolf 3D Printer: AW3D HD Rafts: No Supports: No Resolution: .25 layers Infill: 50-75%

This is a universal filament spool holder for your Airwolf HD 3D printer. It accepts filament spools with a minimum 35mm center hole and a maximum 202mm diameter. Mounts directly to your printer using the existing holes and hardware. Use the...

The standard spool holder supplied with AW3D HD Series printers only fits spools with a large inner diameter. Even though it was designed for Voltivo ExcelFil, it will of course fit all bigger spools and it should be thus a universally usable...

This is a remix of E3D hotend mount for Airwolf HD2x printer. The original mount was redesigned in order to fit two different hotends - one E3D v6 (left) and one E3D Volcano (right). As Volcano is 8.5 mm longeк compared to v6, the mount groove for...

i did like the original setup but i wanna keep it close to the original hot end setup,and maintain the head adjustment also , i did not printed yet but original it is, and works , ill post pictures ones that i have it installed.

Print Settings Printer Brand: Airwolf 3D Printer: AW3D HD Rafts: No Supports: Yes Resolution: .1 Infill: 80% Notes: I printed with PC-ABS with GREAT results. If you haven't printed with PC-ABS, then trust me, all your current frustrations will be...

However when using on the 3d printer I mount it with them hanging down as you then have gravity on your side. Update: 2-14-2018 Just realized that I put up the version without the mounting holes for the raspberry pi. ...There are now two files now,...

Inspired by the legendary Belle Helecopter which fetured in Airwolf I decided to create this epic chopper. Full rotor movement with blade blur, Landing Lights and Strobe lights. Available in the following formats:- Blend file Ply Obj dae and mlt...

You can read more about it at http://airwolf3d.com/blog/2012/10/16/download-and-3d-print-our-functioning-catapult/ Instructions Slice the stl file with your favorite slicer-we run one outer perimeters at 100mm/s and use 35% fill with Slic3r. Note:...

As a kid my favorite show was Airwolf. Created this in Blender and printed it out on our Anet A8. Love the quality.. ...I am going to paint in later on and share the results..

I'm a big fan of this TV series and I've always wanted to print the airwolf model, but the models I've seen are very good but with many pieces, so I decided to make my own design with easy to print pieces, avoiding the use of supports and printing...

3d parts to transform your airwolf 3d aw3d into a direct drive