ak build kits 3d models

 In order to move the extruder backwards 1mm (or rather, the build plate forwards 1mm) it will turn the y motor by 100 steps.  In order to move the extruder up 1mm, it will turn the z motors 400 steps.  Finally, in order to move 1mm of filament into...

If you have the proper filament colors, no painting is needed. The assembled model is 170mm tall. Enjoy! (updated head_with_supports on 11/2/2020 to correct a minor issue when slicing at .1mm layer height)...

I even rebuild my own front switch completely to make it sturdier and with much better grip.Advantages of my designno use of octoprintno smart-plug requireddisconnects the printer completely from power (phase and neutral are disconnected; better than...

Recommend printing in ABS or higher temperature and strength materials, especially if using with a heated build chamber. Post-Printing: Assembly instructions and bill of materials will follow. Parts list: 4-608 bearings 8x22x7 commonly used for...

As for the outer bearing (bottom / on build plate of Pressure Fit print), I ended up using some channellock pliers on the edges of the bearings. Be very careful to not damage the bearing housings. **Note 6**: I would recommend setting the infill...

Not that often, but for me this requires disassembly of a build chamber as well as the printer. I came across and studied Ric-3D’s video (with translations) to try to verify which wire was cut, I created a switch mount that didn’t require any holes...

So all units used for this Dual Extruder is accessible when you build the VORON printers. No need to purchase other new stuff. I have modified the Klipper and slicing software, it worked well when it replaced the old single filament extruder. You...

**Print Instructions:**Supports: noneResolution: .2mmInfill: 15% *************** **Building the model** Colors Black: (Devil Designs PLA - Black)eyeblack_left (print an extra one!)eyeblack_right (print an extra...

In keeping with its eternal purpose of telling inspirational stories about men and women who dared defy convention while walking on untrodden paths to build more compassionate societies, this post would like to highlight the rich cultural...

This is an air purifier, built around readily available commercial parts and printable on most 3D printers with a 220 mm build plate. Depending on your ambitions, it can be a 'dumb' device with a simple on/off switch, become somewhat smart with an...

If you have the proper filament colors, no painting is needed.As presented, Tails is in proportion to my previous Sonic model.Tails can be printed without the base if you want to hang him from a shelf in order to 'fly solo', or printed with the base...

Below is a drawing of the sketch with the correct dimensions.Here are the instructions to build it in SolidworksCreate center rectangle centered on the origin Set as construction geometry Add smart dimensions to constraint box Add...

I had a stash of leftover purple ABS from my last project (Dino Flintstone) and decided to build the Cheshire Cat. My daughter loves Alice in Wonderland, so this was an easy decision for me. The printed model stands 25cm high and 28cm long, but...

Rules (there are several versions)https://www.ultraboardgames.com/stratego/ultimate-stratego.php https://www.ultraboardgames.com/stratego/game-rules.php https://board-games-galore.fandom.com/wiki/StrategoThere are many other Stratego...

Here's the link to the Instructables on how to build and use the POD: http://www.instructables.com/id/Diy-Modular-FPV-Pod-a-Beginners-Guide-to-FPV-for-A/ The FPV pod, or just Pod for short, is designed to be used on any and all of your models! The...

The idea was to create a set of models which would make it easy for someone with zero woodworking skills to quickly, easily, and cheaply build a partition or even a full wall inside a room or apartment without drilling any holes in the walls or...

Some parts will be added in future. If you need additional info, ask in the comments section, so everybody can read it :) Feel free to ask, remix, print, edit and say thanks. After my IKEA Lack table was a bit too unstable for me and would've...

You need to add some light support on the build plate. It doesn't need to be strong as it is there just to help with bridging a back surface. This surface is not visible when the holder is mounted on the rail. The second thing to do is to add a...

The Therion Ifrit is a large model around 120mm tall.  He has been sculpted and posed to print as a single piece on a 5.5" build plate with his base separate.   Presupported files are included for each model in both STL format and LYS (Lychee...

I will update later with what I did.\r\nI plan to make the roads, settlements, cities, build cost cards, and harbor markers out of 1/8" material.\r\n\r\n-All black lines are meant to be cut, and red lines are meant to be etched. They don't show this...

**Building the model** Colors Black: (Paramount3D PLA - Black)eye_black_righteye_black_left.. Yellow: (Paramount3DPLA - Egg Yolk Yellow)beakbeak_without_supports (optional piece)foot_leftfoot_right.. Dark Blue: (Parmount3d PLA - Cadet...

... the corresponding Reddit thread for suggestions. Alternatively, you can comment here. Then I can update the post with corrections or enhancements.Update Post 1 on my method to print parts larger than the build volume : 3Dprinting (reddit.com) 

You can build a single module that renders every part of a project as it appears assembled, then create a presentation layer to isolate a printable part using show or hide. You can go the opposite way, too - you can define a series of components,...

Next up, I'll be building Popeye MK2. When creating my robotic arm, the first step I had to take was deciding what type of electronic components I needed for the arm. I decided to use a Raspberry pi 3 B+ microcomputer as the main computer of the...

The turbo body was designed for Resin printing but FDM should work just fine with proper cooling.[PARTS LIST][V 2.2]:Motor:...

The enclosure makes the motor compatible with the fischertechnik construction toy system, turning it into a 30x15x15mm size building block. The motors run with 12V, but 9V as used by other fischertechnik motors work fine, too.</p> <p>Two versions of...

Print Settings Printer: Adimlab Gantry Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 80% or higher Filament: AmazonBasics PETG Notes: Printed using high density supports (touching build plate only). This will support the recessed hole...

&nbsp;If you have the proper filament colors, no painting is needed.The assembled model is 210mm tall.Enjoy!visor.stl and helmet.slt corrected on...

Allowing students to build parts on the printer and parts from found objects makes this accessible to students with multiple skill levels. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator (5th Generation) Rafts: No Supports: No ...

An LED light bar holder which fits under the MMU unit by clamping onto the underside of its two lower (horizontal) supports. Because it sits just behind the top frame gantry, there is little light shining into one's eyes (unless the printer's high up...