akk diversity module cover 3d models
170346 3d models found related to akk diversity module cover.thingiverse
I leveled the cover so it can be printed without support materials, I also adjusted the height of it so it doesn't squish the OLED screen on the AKK diversity module when it's installed in Fatshark HD3s
thingiverse
- Remix - I made the case deeper and button holes bigger because it didn't fit into my ShenStar D2A DJI goggles analog module adapter - Printed in PETG, 0.2mm, fans off
thingiverse
Iterated-design ORQA FPV cover to fit the FuriousFPV/AKK module using RRA's uploaded source cover. Verified fit with AKK module. Will likely iterate at some point to clean it up but wanted to get this out there so others can get flying with their...
thingiverse
I designed this case for the AKK Diversity Receiver for my FPV goggles. I used 4x 3mm x 8.5mm screws to hold the two parts together. There is a small amount of XY slop as I have found that the boards vary in size and location relative to one...
thingiverse
This is a cover for a module for the following : Flysight Falcon FG02 FPV Video Goggles with DVR HDMI in AKK 48CH 5.8G Diversity Receiver for FatShark Goggles-RX135 The holes for the 3 buttons was a little small, as I was in a rush and needed it done...
thingiverse
__Links to the parts contain Banggood's affilate metadata.__ https://www.thingiverse.com/thing:3500798 # DOCS TODO: * add smaller screw sizes (for the step-down holder inside) # Intro I needed a docking station for the [Eachine...
thingiverse
Eachine EV800 + AKK Diversity RX case This is remix of: https://www.thingiverse.com/thing:2012881 https://www.thingiverse.com/thing:3071967
thingiverse
Added button and display openings to make lid compatible with AKK Diversity out of box. Also added hexagonal air vents to match it a little with the HDZero goggle. This is the third iteration, still some fitment issues as the PCB is slightly mobile...
thingiverse
The cover hold the module in place with a very slight pressure on the OLED board, and the cover itself is fixed with four tabs to the goggle, this tabs have almost the exact thickness to fit between the circuit boards and the goggle. (this gives a...
thingiverse
Work-in-progress Tracking system https://www.virtualpilot.co.uk/index.php?route=product/product&product_id=59 Rx module https://www.amazon.com/AKK-Diversity-Receiver-Compatible-FatShark/dp/B07L2D6FSN (Don't be hating on the colors! ... I was using up...
thingiverse
Added a slot to the original single cover. ...Missed it with the new diversity module. ...Enjoy :)
thingiverse
Wire guide for the cable used for the Diversity module with the Dominator LaForge module. ... I am working on a complete new design that will have the front curve and slots that look more like the original, when I retire in a few weeks I will have more...
thingiverse
The changes I've made have been to the front to get a nice snug fit, with the cover locking into place, along with moving one of the horizontal protectors (on the front as well) to allow the fusion to mount. The front cover is also 3mm thicker to...
thingiverse
I printed this with TPU and with supports. ...I did all measurements on the Fatshark HDO. It requires a longer than stock screw to be fastened as well as the original diversity module cover that comes with the Laforge V4 diversity module.
thingiverse
This is a Fatshark bay door to accommodate the RX5808 Pro diversity module (split version) offered by Ready to Fly Quads. This would likely fit other RX5808 project modules but I have only tested the one sold by Ready to Fly Quads. This door has been...
cults3d
Fat Shark Diversity Module Dock Remixed the original design to fit Joao Reis' PCB board (can be bought direct from him on his Facebook group: (https://www.facebook.com/PCBs_for_FPV-603354826782830/); board is available both assembled and unassembled...
thingiverse
LaForge Diversity module holder for my FatShark Attitude V3s. Made so would look much cleaner and offer much more surface area for 3M double sided tape. Also made a cable track to hold cables on front that is smaller than others I have seen. Printed...
thingiverse
Fat Shark Diversity Module Dock Remixed the original design to fit Joao Reis' PCB board (can be bought direct from him on his Facebook group: (https://www.facebook.com/PCBs_for_FPV-603354826782830/); board is available both assembled and unassembled...
prusaprinters
Fat Shark Diversity Module Dock Remixed the original design to fit Joao Reis' PCB board (can be bought direct from him on his Facebook group: (https://www.facebook.com/PCBs\_for\_FPV-603354826782830/); board is available both assembled and...
thingiverse
The RJXHobby module seems to be slightly bigger that other RX5808 modules. I increased the window by 2mm and had to do some trimming on the inside bottom and both sides to get the module to fit correctly. I went through 3 iterations and this last...
thingiverse
AKK RACE RANGER VTX Cover for Mini Talon Size reduce to 50%
thingiverse
Paint with some model paint or just use a large enough sticker to cover up that ugly paint job :-\ Test fit the laforge diversity module in the hole where the old receiver used to be. Cut off this standoff because it's blocking our connector The blue...
thingiverse
This is a holder+cover for Eachine Pro58 module to be installed on Eachine VR007 FPV goggles.
thingiverse
The main purpose is to fit the AKK x2 ultimate VTX but I also added some small improvements: changed the antenna support from hole to standoff (when using the mmcx to sma cable it's a better mounting IMHO) in 3 sizes. Two of them are designed to be...
thingiverse
Abdeckung für die Lite Version:FatShark Attitude v3 Diversity Cover (Realacc RX5808 Lite) Parts to buy: Realacc RX5808 Pro Made: Made of PLA black (Verbatine) Extruder temperature: 210°C Glass bed temperature: 58°C Resolution: 0.25 mm Infill: 15%...
thingiverse
Works well with my Fatshark Dominator V3 and it covers the cable from RX5808 split diversity receiver (I also used a black braided cable sleeve to hold the wires together). ... I used the tesa® Powerbond Ultra Strong double-sided mounting tape to...
thingiverse
Update: v.1.1.0 [ STL Improved | rounded corners ] Description (EN): In the course of the Airster Community project I created a cover for the conversion of a FatShark Attitude v3 to Diversity (Realacc RX5808 Lite). So that the cover does not look...
thingiverse
Source: https://www.aliexpress.com/item/32968009331.html Many thanks to CABsterFPV, he creates a cover for an other module with very good accuracy of fit. I decided to take the shape of his cover and do some modification for my module. I have...