anet a6 3d model

Human: Anet A6 Lightbar for 5mm Diodes (Version with Holes) or Light Strip (Solid Version) Print Settings Printer: Anet A6 Rafts: Doesn't Matter Supports: No Resolution: .2 Infill: 10% Notes: The railmount should be printed with cutouts facing...

Print Settings Printer: Anet A6 Rafts: No Supports: No Notes: Use 4 loops with a 0.4 diameter nozzle to make sure the walls are solid. It's ideal if your printer is reasonably well trammed (all the axis are exactly at right angles to each other) to...

This was designed to keep the Anet A6 Z axis level as it prints - some users of the Anet reported that the Z axis tilts during prints - mine did this too and one of the Z motors would get out of sync with the other. To tackle this, I created the...

This design draws inspiration from similar creations on Thingiverse, tailored specifically to the Anet A6. It enhances extruder resolution by 3.75 and requires a corresponding increase in extruder steps before fine-tuning. Upon printing and...

Human: Custom fan mount for Anet A6 featuring BLTouch sensor integration and X-axis cable chain attachment. All required chain components can be sourced from the original design on thingiverse.com/thing:2168268. This modification allows for full...

... ... Print Settings: Printer: Anet A6 Rafts: Doesn't Matter Supports: Yes Resolution: 0.3mm Infill: 20% Notes: I added 2% extra size to account for ABS shrinkage, but it turned out too big and fits tightly on the screws. I also used brims for printing.

The stock Anet A6 printer fan duct falls short in several areas. It's too brief, forcing air directly onto the nozzle rather than the print surface. Having successfully implemented a Prusa i3 Mk2-style fan duct on a previous project, I designed...

I'm excited to share this Remix of the brace for the Anet A6, as I recently discovered some errors in the .stl file that would have caused the print to fail. While not particularly dramatic, I still wanted to address these issues. Since I really...

These sockets can be installed on top of the ANET A6 printer to illuminate the heatbed. Two holes are available on the side for this purpose. To activate the light, four LEDs with 3mm diameter and one 100-ohm resistor need to be soldered in series.

Printing Flexible Filament on the Anet A6: A Step-by-Step Guide To successfully print flexible filament on your Anet A6, it's essential to follow some key guidelines. First and foremost, ensure that your printer is calibrated correctly. This involves...

bien no tiene que tener problema) y seguramente lo que te esté pasando es que Z se suba o baje de un lado más que del otro.Correa GT2 cerrada 6m/m ancho y un perímetro de 1100 m/m...

Print Settings: * Printer: Anet A6 * Rafts: No * Supports: No * Resolution: .1 * Infill: 30% * Notes: Tight fit – sanding may be required after printing to achieve smooth movement. I used brute force, but printing a new fan might be necessary if...

This design serves as a mounting bracket for a 3D-Touch or BL-Touch sensor on an Anet A6 3D printer, enabling auto bed leveling functionality. The bracket allows for the sensor to be mounted directly beside the extruder nozzle at its right side,...

I was recently informed that while the Anet A6 printer has a maximum build height of 250mm, the clearance between the gantry (x-axis) and the encoder wheel (menu button) is extremely slim when printing at maximum heights. Adding this light bar may...

Print Settings (note these settings are with Craftware) Printer: Anet A6 Rafts: Doesn't Matter Supports: Yes Resolution: High Infill: 15% Fusion: 200 degrees C Notes: Please note that these are Craftware settings and I have no idea what they would...

Important Note: The original firmware on the Anet A6 does not support the BLTouch, and electrical modifications are necessary to integrate it properly. All parts were printed with a 0.2 layer height setting for high-quality results. PETG filament...

I had some Problems Whit the basic stiffness of the Original Anet A6. Therefore I decided to design some printable part to improve this. This ended up in an almost complete redesign of the printer. While doing so I also changed some other...

Anet A6 power switch --------------------- I created this power switch for the back of my printer because I couldn't find an existing solution to install one at the original power supply location. ### Installation The top hole of the switch is...

A replacement fan duct for the Audi A6, designed to fit precisely and securely. ...Simple plug-and-play installation ensures seamless integration.

I noticed that the heat bed cables on my A6 were starting to suffer metal fatigue due to the constant motion, so I've produced this part to fix them in place. I use spring covers (https://www.thingiverse.com/thing:2044042) so this part is designed to...

A clip that halts the vibrations of the Anet 12864 LCD display during printing.

This is a protective covering for the blank spaces within your clear plastic border. ...Simply take off the screen panel from your device, which is commonly referred to as the A6.

This 33mm laser printer stand for Annet A6 features a secure attachment via two M3 bolts and nuts. ...A convenient tray sits atop the bed, positioned perfectly alongside the printer.

Small support for Anet's front plate to stop it from bending when tightening the Y-belt. ...

It's probably not suitable for A6 models with original Z-carriers due to a slight protrusion in the X+ direction. The printing process is slightly more complicated because the nozzles are positioned downwards. Unfortunately, it wasn't possible to...

... was specifically created to accompany the Probe And Fan Mount found at https://www.thingiverse.com/thing:2424312. However, it's worth noting that when installed on a standard A6 mount, the nozzle might not be perfectly centered along the Y-axis.

Because I removed the displays of my Anet printers to free up space for the X wagon at the top of the X axis, I came up with a solution that involved creating new housings for them. In the end, I designed and printed four different models, but only...

This is an enclosure for the A6, designed to be plug-and-play compatible without requiring any modifications or cable disconnections - it's actually recommended to tidy up cables before connecting them. ... If you find this video informative, please...

I noticed that the heat bed cables on my A6 were starting to wear out due to constant motion, prompting me to create a solution. To prevent further damage, I've produced this component to securely fasten them in place. To achieve this, I employ...

Anet A6-A8 Quick Fan model