anet a6 instruction manual 3d models

So if you're not confident with Fusion360, you'll need to read my step-by-step instructions below. It's limited to circular pipes and ports. While most ports are circular, and this will be widely compatible with many tools.... There's a TON of tools...

Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: bar_length_trim = 0 lug_text_distance = 2 outer_margin_width = 1 ruler_unit = 10 barextruder = extruder1 lug_width = 5...

The adapters, braces, instructions, hardware, etc., are identical to those used on that housing. Ignore any parts labeled as "SR" included here, they will work with this mount. I also remixed TheStankec's QQS pro volcano fans, because I liked the...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 30 shape =...

Instructions: - Border width: 1 - Mode: Compile - Pixel shape: 4 - Panel shape: 0 - Pixel size: 0.699 - Orientation: 1 - Thickness: 0.5 - Picture: [0.224, 0.251, 0.278, 0.376, 0.369, 0.278, 0.310, 0.584, 0.337, 0.275, 0.286, 0.294, 0.282, 0.263,...

It has a break-action and is breech loaded. DISCLAIMER: By downloading these files, you agree that I shall not be liable for any damage, injury or harm resulting directly or indirectly from the use of these files or instructions. Always be safe and...

See my attempt to play Pepsiman here on the Super Retropiepod: https://youtu.be/-517g8r_IGU #Instructions Below! I wanted to make a portable Pi gaming thing for my dad for christmas. I downloaded, printed and checked out a few but.... I dunno, I'm...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

So I made a spring tensioned camera holder instead. Printed parts needed to make thisBaseCameraBaseCameraLidLeftHolderMiddleHolderRightHolderSpacerX3                          ...

I'm even powering the RPi from 5v from a spare endstop pin off the Mini RAMBo - who has 3hrs to same-dayAmazon' yet another USB charger ? No metal fasteners needed (the MK2 comes with an extra 12mm M3 screw to replace the stock 10mm one as part of...

It gets accurate time through NTP and lights appropriate LEDs (WS2812b) to cast a shadow indicating the hour. Print instructionsThe Clock The creation and how it works can be seen in the video: It proudly hangs above our bed, it seems very bright...

This tube has only been tested on a "Nikon F" film camera (1959), please verify that the printed mount does not collide with any new mount features introduced in newer electronic cameras.If you like macro photography then check out my other designs...

(Info on reading Vernier scales in full-screen picture above, as well as here: https://en.wikipedia.org/wiki/Vernier\_scale) Released not fully complete in order to support the ongoing XY calbiration discussion at:...

###Printing instructions - Material - ABS/PETG/Flex - Nozzle - 0.3 mm - Layer - 0.15 mm - Infill - 40% - Top/bottom - 5-6 layers - Walls - 4-5 layers Use raft and supports, see proposed printing layout on picture **printing.jpg**. ###Assembly...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

The control APP has been created with Python Print instructions This 3D printed Pybot SCARA Robotic arm has been created using common and affordable elements from the 3D printed World (NEMA 17 motors, Linear bearings, timing belts...) The idea was to...

Now 2 sizes and they bear marks which screw size they are for.Update 2018-01-27 Added stapler clips.Added clip alignment helper toolsPrint instructionsResolution: 0,15Infill: 50%Notes:All objects here are either designed to print without support or...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

 ##TLDR Instructions todo:  The following...

Print “Ikea_Lack_Hinge_V4_UpperLowerTableMiddle_Print4” four times, all other parts are needed only once.Also get 4 felt gliders to avoid a hard “bang” when you close the table.You also need 6 small screws (which fit into 3mm screw holes, just to...

4.7" naval guns. Drawn in FreeCAD. Changelog 2/12/21 Chamfer trunnion clip: for easier press-fitting Bulk up carriage: needed more thickness under the spring retainer Axles a separate part: lets them print vertically, which means no support needed...

N.B: per fissare lo sherpa rimuovete un attimo la vite con la molla (quella che serve a far pressione sul filamento) 10) ora inserite il filamento, inserire la vite con la molla e stringete (non troppo eh !) B) SHERPA: 1) ecco un paio di link per...

Holding his C-14 Gaus Rifle close to his powered armor suit, the Marine is in standby mode, awaiting instructions. This accurately designed 3D model complements the Terran Marine with the rifle pointed up. Print them and gather your own infantry of...

Instructions for programming this can be found on the product page and it's very simple.  I'm still in the testing phase but as of now I am disconnecting at 36 volts and reconnecting at 39 volts (read as “3” on the module).</li><li>You will then need...

Slotin instructed one of his colleagues to lay radioactivity-detecting film badges around the area, which required the scientist to go dangerously close to the still overheated core. The errand resulted in no useful data, and was mentioned in a later...

All of the 3D files and information on other parts needed are provided along with easy to follow assembly instructions. The basket is not quite at the scale of a full mini basket but a regular mini does fit inside. It is primarily intended to be...

Tips for speed/accelerations printing direct: !It is highly recommended that you first install this firmware by calibrating and configuring it according to the instructions: Anycubic Mega marlin 1.1.9 Outer shell Speed 30 mm/s, acceleration 800. Top...

Follow the instructions for an easy and correct assembly process.After being 3D printed, Vulcan 3D model will stand 214 mm wide, 166 mm tall, and 280 mm depth.Buy Vulcan Tank 3D model STL files by clicking the green Buy button in the top-right corner...

This is a 7mm thick spinner. Print instructionsCategory: Mechanical Toys Summary My take on the tri-spinner fidget toy. You will need 4 standard skateboard bearings, 22mm OD / 8mm ID / 7mm Thick I prefer the Thicker Spinner Body (this is what is in...

Optional magnets provide a gentle hold against the backer.• Designed for larger and easier to install wood screws over the original lack enclosure drawer design.HARDWARE• Screwdriver• Countersunk woodscrews: (Metric: 4x25mm to 4x16mm) or (SAE: #16 or...