anet a6 instruction manual 3d models

Print Settings Printer: Anet A6 Rafts: No Supports: No Notes: Use 4 loops with a 0.4 diameter nozzle to make sure the walls are solid. It's ideal if your printer is reasonably well trammed (all the axis are exactly at right angles to each other) to...

This was designed to keep the Anet A6 Z axis level as it prints - some users of the Anet reported that the Z axis tilts during prints - mine did this too and one of the Z motors would get out of sync with the other. To tackle this, I created the...

I have the Anet printer and it has a frame of the Anet A6 but with the button panel of the Anet A8. While searching among existing models to place a switch, I realized that none of them would work for me because they all had two sides and in my case...

This design draws inspiration from similar creations on Thingiverse, tailored specifically to the Anet A6. It enhances extruder resolution by 3.75 and requires a corresponding increase in extruder steps before fine-tuning. Upon printing and...

These sockets can be installed on top of the ANET A6 printer to illuminate the heatbed. Two holes are available on the side for this purpose. To activate the light, four LEDs with 3mm diameter and one 100-ohm resistor need to be soldered in series.

The stock Anet A6 printer fan duct falls short in several areas. It's too brief, forcing air directly onto the nozzle rather than the print surface. Having successfully implemented a Prusa i3 Mk2-style fan duct on a previous project, I designed...

This is a custom filament holder designed specifically for the Anet A6, allowing users to mount it securely on one of the cable holes in the left top support plate. A thoughtful gap has been included for the cable bundle, ensuring that cables can...

Chciałem, żeby też współpracowała z modyfikacją https://www.thingiverse.com/thing:2620320 Potrzebna będzie: 2x stara dysza gąbka Gwintownik M6 Można też zastosować szybkozłączkę do rurki PTFE Print Settings Printer: Anet A6 Rafts: NoSupports: Yes...

Human: Custom fan mount for Anet A6 featuring BLTouch sensor integration and X-axis cable chain attachment. All required chain components can be sourced from the original design on thingiverse.com/thing:2168268. This modification allows for full...

This is a versatile extruder light for the Anet A6 designed to illuminate the printhead during printing sessions. The part features strategically placed holes that securely hold LED cables in position using zipties. To ensure optimal performance,...

I'm excited to share this Remix of the brace for the Anet A6, as I recently discovered some errors in the .stl file that would have caused the print to fail. While not particularly dramatic, I still wanted to address these issues. Since I really...

... ... Print Settings: Printer: Anet A6 Rafts: Doesn't Matter Supports: Yes Resolution: 0.3mm Infill: 20% Notes: I added 2% extra size to account for ABS shrinkage, but it turned out too big and fits tightly on the screws. I also used brims for printing.

I drew up the Anet A6 primary components before assembling it, anticipating potential upgrades to aluminum later on. It's possible that these diagrams will prove useful to someone here, so I'm sharing them now. If any of you notice discrepancies in...

Anet A6 lightbar for 5mm diodes (version with holes) or light strip (solid version) Print Settings Printer: Anet A6 Rafts: Doesn't Matter Supports: No Resolution: .2 Infill: 10% Notes: The railmount should be printed with the cutouts upward. Try...

Print Settings (note these settings are with Craftware) Printer: Anet A6 Rafts: Doesn't Matter Supports: Yes Resolution: High Infill: 15% Fusion: 200 degrees C Notes: Please note that these are Craftware settings and I have no idea what they would...

I've decided to upgrade my Anet A6 printer to Prusa specifications. I've opted for a modified x-axis design similar to the original Prusa model, as it's undoubtedly the best solution available. To implement this change, I also had to modify my...

... 0.2 layer height, and 40% or higher infill. Printer Settings: * Printer: Anet A6 * Rafts: Doesn't Matter * Supports: Yes * Resolution: 0.2 * Infill: 40% * Notes: Use high infill, preferably 100%. ...Thin walls of 0.4 will help with support removal.

Important Note: The original firmware on the Anet A6 does not support the BLTouch, and electrical modifications are necessary to integrate it properly. All parts were printed with a 0.2 layer height setting for high-quality results. PETG filament...

Anet A6 power switch --------------------- I created this power switch for the back of my printer because I couldn't find an existing solution to install one at the original power supply location. ### Installation The top hole of the switch is...

I had some Problems Whit the basic stiffness of the Original Anet A6. Therefore I decided to design some printable part to improve this. This ended up in an almost complete redesign of the printer. While doing so I also changed some other...

A replacement fan duct for the Audi A6, designed to fit precisely and securely. ...Simple plug-and-play installation ensures seamless integration.

Like I said none of these really do fit as when you have to scale them when slicing it comes out of proportion and its not working. I had a specific Power rocker switch with fuse that I wanted to use. So I designed this very crudely but very...

A clip that halts the vibrations of the Anet 12864 LCD display during printing.

This is a protective covering for the blank spaces within your clear plastic border. ...Simply take off the screen panel from your device, which is commonly referred to as the A6.

This 33mm laser printer stand for Annet A6 features a secure attachment via two M3 bolts and nuts. ...A convenient tray sits atop the bed, positioned perfectly alongside the printer.

bien no tiene que tener problema) y seguramente lo que te esté pasando es que Z se suba o baje de un lado más que del otro.Correa GT2 cerrada 6m/m ancho y un perímetro de 1100 m/m...

Print Settings: * Printer: Anet A6 * Rafts: No * Supports: No * Resolution: .1 * Infill: 30% * Notes: Tight fit – sanding may be required after printing to achieve smooth movement. I used brute force, but printing a new fan might be necessary if...

Small support for Anet's front plate to stop it from bending when tightening the Y-belt. ...

... was specifically created to accompany the Probe And Fan Mount found at https://www.thingiverse.com/thing:2424312. However, it's worth noting that when installed on a standard A6 mount, the nozzle might not be perfectly centered along the Y-axis.

This is an enclosure for the A6, designed to be plug-and-play compatible without requiring any modifications or cable disconnections - it's actually recommended to tidy up cables before connecting them. ... If you find this video informative, please...