anet a6 upgrade extruder 3d models

I also loosened the tension on the extruder gears to where it barely closed onto the TPU. The filament stripped the first two times I tried to print the parts. When I finally printed the parts correctly, the TPU parts had a lot of stringing, but with...

** you may need 3 to 6 3mm flat washers for shims I printed using Monoprice PLA+ with extruder temp of 200 and bed temp of 45. The initial layer is 210 and 50 to aid adhesion. I have the stock V2 hot end and a glass bed with buildtak on it. ... The...

The paint inside the conical hollows of the blue version is simply flat white latex, which sticks well enough due to the texture of the extruded PLA; the black die is made out of ABS with white appliance touch-up paint. The black hollows of the white...

Each game figure needs to be printed out separately rather than in groups like had those originally setup; I thought the grouping would provide printing efficiency but printing that way caused the extruder head to knock them over once those were...

Due to the twin storey configuration it wasn't possible to feed the filament from above the bottom printer, so I decided to design a filament feed guide that would allow the filament spool to sit alongside the printer.As part of the design I wanted...

Past für Bowden Extruder (kein direkt Drive!) Past für alle FW`s die im Original Zustand auch laufen. Die Platinenbox ist Variante V1 (verklebter Stecker), da ich keine V3 Platine besitze konnte ich sie nicht zeichnen. Sorry. Das 16 adrige 0.14...

Note that if you find that both the nuts and the bearings don't fit, you should calibrate the flow and steps on your extruder since those will affect the fit. The updated version is "V6" and all the parts and STP file have been updated with this...

I found, though, that I needed the air to go more horizontally to directly below the nozzle as the extruded filament wasn't always cooled quickly enough (I use a volcano set). So I made a version (version 2) duct with openings that are more...

Please note when scaling down you will loose detail , if this is the case, resize the svg (or bitmap before converting.[logo position x] and [logo position y] You can adjust the x and y position with the respective position sliders. The logo extrudes...

This is particularly useful for those expensive filaments that come in narrow 500g rolls and for the wide 2Kg spools.I set my dryboxes on a shelf above my printers and feed directly into the extruder. Yes, it works on a Prusa XL too (no more feeding...

If you are over extruding, the LED mounts won't fit very well. Wiring the the LED strips: I am using a standard 5050 white LED strip. I took a segment of 12 LED's and cut them down the middle (two segments of 3 LED's each). So there ends up being a...

Essentially, you first find the relative offset of the probe relative to the extruder hotend. Then you calibrate the probe Z-offset using the PROBE_CALIBRATE command. Just for reference, this is my Klipper probe section: [probe] pin:...

If your printer is under-extruding or having any other issue that could affect the strength of the print then you might get completely different results and it could break on you while using it. I have included infill objects to be used to override...

See Assembly.jpg The electronics can be placed in the wire_cover_extended of the extruder. I needed to reverse the polarity of the sensor ring to the circuit (+ side on - pin). Polarity can be tested by slowly pressing on the nozzle and then...

(The toothbrush still shouldn't fall out, but a hole any larger and it might...)(I also use a print of the original model as a holder for fine detail paintbrushes, so a hole in the bottom of that one would be rather pointless.)Enjoy!Print...

This turned out to be a lucky accident as it showed the following: First - cylinders printed in that version had poor bending strength (already knew that, actually). Second (and more important) - what makes the crush ribs work is not so much that the...

You can print in Vase mode with a 0.8 mm Nozzle, 0.6mm, 0.5 mm or even 0.4 mm if needed OR print Normally with a 0.4 mm Nozzle extruding two perimeters with the Model having 0.6 mm thickness to allow for extrusion Overlap of 25%.All the Sketches...

This will help to prevent warping from the heat of the LED ring.I use an enclosure for printing, so the light levels aren't great, I have a strip of LEDs mounted to the top of the enclosure, but whatever is being printed is pretty much in shadow...

For example, extrusion-based printing has the constraint that extruded material must be self-supporting. There are also less obvious constraints that are just as important; for example, a printed spring cannot be under tension as it is printing, so...

I'm printing on a FlashForge Dreamer in ABS using Simplify3D with the following settings: No support No rafts 100% fill 0.2mm layer height ABS slurry on the special print bed surface 105c print bed temperature 230c extruder temperature Black...

Also, that way the connections wouldn't be available to make any shorts or be unintentionally damaged. The holes could be a bit smaller :) Final desing: top and bottom look the same (connections are hidden inside the plastic part) Making the STL...

After that, I may add fins in the open position where the blade extrudes, so stay tuned! December 22, 2019: So I uploaded pictures of what my print looks like, and I'm modifying a couple of dimensions very slightly (it's honestly really close right...

The top cover was just the top edge of the base/housing, copied-pasted-extruded. For the blades, I used a dead squirrel cage fan as a guide, first drawing one simple, rectangular blade placed right on the edge of and tangent to the hub. Then I...

Note that this thing does somewhat block the view of the extruder lever from the front (the lever can still be used, it's just harder to see). Makes filament changing a bit more awkward. Additional Info Other Hardware: M3 screws and nuts (2...

The above code is more straightforward and easy to understandG92 E0.0M104 S{(temperature[0]+10)-(5*int(((layer_num-6)/50)))};[layer_z]The STL is edited after I printed it for even numbers and 3mf file is updated with new STLPrint was aborted due...

The thermostat will therefore regulate the temperature of the box so that it is neither too cold nor too hot, Functioning : In our case, the temperature rise is not a problem because the extruders and the heating mats emit a lot of heat. This is why...

The originals had a 0.5mm gap (a total of 1.0mm of free play) between the threads, which wouldn't allow parts to be tightened without the nut slipping, especially on a printer that's under extruding. Nearly every facet has either been enlarged,...

Then move the extruder carriage manually to each position. When adjusted right, you want the entire motion distance between the bed and the bottom to be minimal. The trick to getting this right are the springs. These springs are the right size and...

TL;DRA faster and handy way to calculate the extrusion multiplier. Collectiontools, 3D printingMotivationWhile working with several layer heights between 0.10 and 0.48 mm combined with extrusion widths between 0.2 and 1.6 mm we observed that...

Used in tandem with the filament wheel at the bottom, it is quite beautiful to see all the wheels move together with the extruder. Photos added. You'll notice the mount looks bent; it is. After sanding I like to heat my plastic with butane hand...