anet a8 e3d v6 titan

My anet a8 pinter now back to business. The direct drive system on anet a8 has broken 2 months back it stops working from there. I tried a lot to fix it But could not. Hence i decided to change to E3D hotend which is less issued has compared to...

This is an 18mm inductive sensor mount designed specifically for the new E3D Hemera Hotend, which will be attached to a custom mount created by Thomas Sanladerer: https://www.prusaprinters.org/prints/12763-e3d-hemera-upgrade-for-the-anet-a8 You can...

I was upgrading my Anet A8 into a Bowden setup and the demand for this design suddenly popped up in my mind. As I looked at Arjjck's circular nozzle fan design (https://www.thingiverse.com/thing:1620630) for the original A8, I really liked it, but...

As a result, I decided to switch to an E3D hotend, which is known for being less prone to issues compared to the direct drive system on my Anet A8. However, I soon realized that changing the filament would be a real challenge. I have to say, I'm...

NEW DESIGN https://www.thingiverse.com/thing:4290427 ------------------------- Not a Remix, but a addon for Anet A8 Direct Feed E3D Carriage Mount https://www.thingiverse.com/thing:2628855 Holder for BLTOUCH Offsets: X probe Offset -25.6 Y probe...

NEW DESIGN https://www.thingiverse.com/thing:4290427 Not a Remix, but a addon for Anet A8 Direct Feed E3D Carriage Mount https://www.thingiverse.com/thing:2628855 Holder for BLTOUCH Offsets: X probe Offset -25.6 Y probe Offset +8.5 10.03.2020 add...

Remixing the E3D Clone is a bold move that combines the precision of a replica with the adaptability of a chain. ...This innovative approach yields an Ensen Square, a unique assembly that unites disparate components in a harmonious union, challenging...

Reworked from these designs - http://www.thingiverse.com/thing:1633606, http://www.thingiverse.com/thing:815725, and http://www.thingiverse.com/thing:926794. ...I have this setup on my Anet A8, and it operates flawlessly.

Here is the rewritten text: I crafted this vertical x carriage for my Tevo Tarantula to seamlessly work with E3D Titan and E3D V6 hotend direct drive. It accommodates stock screws effortlessly. Notably, print belt holders must be printed with 100%...

This is a customized remix of the fanduct designed by Carsten Heuer, tailored specifically for an E3D clone that's slightly longer than the original. It features a unique design that allows only 2-3mm of the nozzle to extrude, ensuring the airflow...

A new fan duct has been incorporated due to the longer heating block, which replaces the original Anet design. Additionally, zip tie holes have been included for added flexibility. X-Carriage Updates: a) A dedicated space is provided for an LED...

I'm thrilled to share my very first creation - a clever E3D mount designed specifically for the A8, featuring a handy cable chain attachment. This innovative mount expertly positions the extruder, ensuring that the nozzle remains perfectly centered.

Wider fan duct for Anet A8 e3s clone mount - the solution to a nagging problem: the original mount wasn't properly aligned with the nozzle. Check out this clever fix on Thingiverse: https://www.thingiverse.com/thing:2628855 Printing this mount is a...

This is a fresh take on my Anet A8 BLTouch Holder, designed for mounting directly in front of the extruder fan. ...This iteration has been precision-crafted to work seamlessly with the Hemera Extrusion system and Tom's Fan Mount Adapter, available at:...

The V6 mount has been shifted over 10mm to the left, so you're good to go without any changes. This meant moving the fan to the right - and I've included a special fan duct for this purpose. I upgraded the clamp for the V6. Now you can use two 20cm...

Any similar solution that clamps to a V6 hot end should work, as long as it clears the BMG extruder. 8-10-18 I worked up a better cooling solution for the hotend and using a 5015 radial fan for parts cooling, I've uploaded it separately here -...

I reimagined the original layout to incorporate a 40x40mm cooling unit.

Any similar solution that clamps to a V6 hot end should work, as long as it clears the BMG extruder. 8-10-18 I worked up a nicer solution for cooling the hotend and using a 5015 radial fan for parts cooling, I've uploaded it separately here -...

Because the filament is still passed through a short Bowden tube, the module will most likely still work with a genuine E3D Titan or a similar extruder, but this may put the tube at an angle and/or require a longer/shorter tube. Adjusting the offsets...

Because the filament is still passed through a short Bowden tube, the module will most likely still work with a genuine E3D Titan or a similar extruder, but this may put the tube at an angle and/or require a longer/shorter tube. Adjusting the offsets...

My "Squall" Titan Aero mount can be found here: https://www.thingiverse.com/thing:2854008 The fan mount/housing is available here: https://www.thingiverse.com/thing:895762 It's a great addition, and works flawlessly! However, I did need to use...

The nozzle fan for the E3D carriage was created by a talented individual named Toosha, and we're grateful for his contribution to the community.

https://www.thingiverse.com/thing:2972363 Re-Modeled shorter to accommodate E3D hotend modification. Uses existing holes and screws for mounting. ...

His original design was unfortunately meant for 45mm rod spacing (older a8's), lacked a decent z probe mount solution (other remixes with probes were off mark IMHO), and had some minor design issues (mainly the X-belt hole fit, and cooling flow...

... I was perplexed by the absence of a probe sensor mount on this carriage, so I promptly created one in under 5 minutes using 3D Builder. This makeshift solution performs adequately for now. I utilized the Bracket_part_2_6mm to attach my E3D clone.

Here's a complete redesign of my previous attempts at creating a dual E3D mount, with a focus on achieving the following design goals: 1) A modular design that allows for quick part exchange 2) An easier mechanism for height adjustment of the J-head...

To create a carriage that could accommodate dual nozzles while retaining the stock direct extruder's efficiency with flexible filament, I incorporated an E3D remote extruder for reduced weight. The z-probe sensors were positioned 18mm from the...

The mount body with direct e3D Titan Extruder support. All parts of original Heavy Duty and modules are compatible with this mount body. Supports up to Nema 17 34mm stepper motors without problems (Tested on Ender 3) Update 04/16/2021 - Added...

Moved the screw hole 5mm upward to accommodate the new style Titan cover, which I've sourced from a Chinese clone. I printed mine in Colorfabb XT with no supports, and while I'm not entirely blown away by the overhangs, it will suffice. The design is...

Moved the screw hole 5mm up to accomodate the new style Titan cover. I have a chinese clone.<br/> I printed mine in Colorfabb XT (no supports), not too impressed with the overhangs but it will work. ...Great design!<br/> EDIT: Can be combined with...