anet a8 fan duct 3d models
136380 3d models found related to anet a8 fan duct.
thingiverse
This is a remix between the stock Anet A8 fan duct and the semi-circular fan duct. In my opinion the direct air flow is the best but design of the stock fan duct is flawed and result a whistle. ...Here I have fixed this problem.
cults3d
This is a remix between the stock Anet A8 fan duct and the semi-circular fan duct. In my opinion the direct air flow is the best but design of the stock fan duct is flawed and result a whistle. ...Here I have fixed this problem.
thingiverse
Anet A8 original fan duct. This is a Remix (made from scratch) of ms3dp's fan duct, because his neck is to short.http://www.thingiverse.com/thing:1438439 Note that the support is only in the neck so you can remove it. The model is rotated so the...
cults3d
Improved Anet A8 Fan Duct. This has a semi-circular design in order to not interfere with the heater block wires, and an optional stem that prevents the fan duct from falling off mid print. Tolerances around the stem join are 0.1mm, so it is a...
myminifactory
This is a fan duct for the Anet A8. ... I had to design a custom one, because I'm not using the stock nozzle. This design is about 10mm taller than the other models I've seen here.
thingiverse
Slanted Circular Extruder Cooling Duct for the Anet A8 that doesn't crash into the clamps holding the glas bed. It is also a little wider to allow for the hotend to be on the same level as the cooling ring. Please note that this cooler is pretty...
thingiverse
Even after a PID tune, the fan would trigger a thermal runaway because my nozzle was lower and the fan was cooling the heater block. So I designed one with an 8mm drop, which was too low. I redesigned it with a 4 mm drop, which worked for a bit...
thingiverse
It is a remix of the lokster Semi-Circular Anet A8 Fan Duct (https://www.thingiverse.com/thing:1954001), but is lower to fit in the ANET A8 | Customizable E3D v6 Carriage / Bowden Mount (https://www.thingiverse.com/thing:2099577). ... My hotend is a...
thingiverse
This is a remix of the Anet A8 Fan Duct Spaceship edition by paul0. I really liked his design, but I couldn't use it because of my auto leveling sensor. I remixed it with a holder for an 18mm located directly in line with the extruder nozzle using...
thingiverse
Check out some of my other open source stuff at http://lokspace.eu If you have problems slicing / printing the normal version, try the "thick walls" version - "Spriya - Anet A8 Fan Duct - Thick Walls.stl" found in the archive (it has 1.2mm walls, but...
thingiverse
This is my version of the "circular fan duct" for the Anet A8 printer (and other compatible printers). ... Ayman hasan
thingiverse
EDIT: My new Version V2 is now online here: http://www.thingiverse.com/thing:2186878 A short Version of a Fan Duct for the Anet A8. ...It fits perfectly in this Fan Holder: http://www.thingiverse.com/thing:2151906 Print Settings Printer: Anet A8 Rafts:...
thingiverse
... design to print such that there are no bridges or overhangs. ...Tape the two halves together with duct tape and you have a passable fan duct. ... To use the scad file you'll need to download the stl file for the original fan duct this was remixed from.
thingiverse
- - - V2.0 (2017-10-07) - I have completely redesigned the fan duct and now it works as I imagine. Improvements to old version: (old version is in zip-file) - easier to print - bigger tube - better air flow at all holes - corner bevelled to...
thingiverse
Hat eigentlich als Scherz begonnen. Die Düsen-spitze von nem Freund ist immer abgefallen, da hab ich gesagt " ich mach dir eine die passt ". Dann hab ich gefragt ob er lieber große Hupen will oder nen runden A*sch. Du brauchst Support und...
thingiverse
Part cooling fan duct for use with [Anet A8 E3D v6 carriage](https://www.thingiverse.com/thing:2099577) and the E3D hotend
thingiverse
This is a remix of 2 things, it support the BLtouch and the fan duct. It work perfectly with anet A8. ... Enjoy
thingiverse
I can't mount the Anet A8 Fan Duct Spaceship edition ( https://www.thingiverse.com/thing:2088006 ) with the fan holder in the picture, so I remixed it
cults3d
I can't mount the Anet A8 Fan Duct Spaceship edition ( https://www.thingiverse.com/thing:2088006 ) with the fan holder in the picture, so I remixed it
thingiverse
This is a New Version of my last Short Fan Duct for the Anet A8. ...Now he fits better and stronger in this Fan Holder http://www.thingiverse.com/thing:2151906 Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 50
thingiverse
A fan duct for the Anet A8 3d printer This is my own Fan duct for the Anet A8 I have found many fan ducts on here but printed a few and they just didn't work for me the bottoms are offten flat and the flat bottom sits very close to the heatbed which...
thingiverse
... - simplifying the mesh, adding the new attachment part etc. Note: there is newer, and more effective fan duct I designed: http://www.thingiverse.com/thing:2133328 Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2
thingiverse
This is a bionic approach of a fan duct for the ANET A8. Optimized for low pressure air flow aiming at the tip of the nozzle and the part (that is to be printed). Best print with support as shown in pictures above for smooth surfaces on walls.