anet a8 guide 3d models

Guide rods are held firmly in place by robust holders that secure them along the Y axis.

Fast and efficient filament guide in action! ...Printed at top speed of 50 mm per second, with a solid infill of 20% density, all within under 10 minutes.

Add a 3cm 4mm PTFE tube to your filament guide for effortless printing. ...With this upgrade, you'll experience reduced friction and zero jams.

It is made to fit the A8 Prusa i3 clone, on the side opposite of the Z-Axis Limit Switch, utilizing the same mounting holes that are pre-drilled. The threaded fitting takes a bit of muscle to get started, but will sit flat, and the hole from the...

I designed a custom version of the filament guide from https://www.thingiverse.com/thing:1764285, which itself was created by remixing another design at https://www.thingiverse.com/thing:1711086. ...This redesigned guide fits snugly on top of my display...

To overcome this issue, I created custom guides allowing wheels to rotate freely during printing. This eliminates the risk of filament getting stuck in the guide. Both designs have been printed and used successfully. However, I prefer the double...

... fantastic design by Leo_N adding a funnel for the filament. ...The idea of the funnel is taken from [this](https://www.thingiverse.com/thing:2357589) other design that I had on my printer until switching to my own filament guide.

I Recently Upgraded a Smart Filament Guide and Filter Design, Enhancing Its Resistance to Fatigue Stress Caused by Retraction. The Original Design Was Found on Thingiverse as #2524232. It Had Been Printed Successfully Earlier, But Further...

This innovative filament guide features a single 608 bearing, carefully salvaged from a broken fidget spinner. As I've positioned my filament spool to the left of my trusty printer, I aimed to minimize friction, making it effortless for the stepper...

I took the design into Tinkercad and made some modifications to the guide, while leaving the mounting plate and arm intact. ...After slicing a 1.8mm opening to allow for easy filament insertion, I was able to get it working for myself, although results...

A straightforward filament guide designed to elevate the filament over the right-hand side of the printer and prevent it from getting caught in a joint. This was my first real-world application of Fusion 360, and I've included the .f3d file for...

Version 3 available at https://www.thingiverse.com/thing:2895215***\r\n\r\nI only needed the Filament Guide part for a PC4-M6 push fitting of this, so I removed the fan holder.\r\n\r\nAdditionally, I added another version without screw holes to allow...

I was thrilled by the concept of this revised guide, which prevents filament from scraping against the metal extruded bracket hole, thus eliminating annoying shavings everywhere. However, I encountered an issue when utilizing it with a linear chain -...

Remix of Thorinair's Improved Anet A8 Filament Guide for mounting vertically rather than horizontally. ... Designed to work seamlessly with custom extruder fan top-mounts, such as the one located here or this remix thereof.

This is a simple clip that will attach to the generic acrylic Prusa i3 style printers you buy on Amazon for cheap (I have an Alunar). Maybe I'm just an idiot, but I couldn't find this posted anywhere. The clip allows you to secure and center your...

I wanted a base that's easy to assemble, so I designed it with slots and screw holes on the walls. This way, if the base does tend to shift slightly, you can secure it with M3 bolts. Set screws are usually small enough to self-tap with their own...

Simple mesh for extruded material. Insert a pliable absorbent substance thoroughly. ...Version R5 includes also a structural support for extruded material, preventing friction between the extruded material and the mesh.

I stumbled upon more impressive designs, but I'm choosing to keep this one around. ...To get it printed smoothly, align the pulley so that it's parallel to the bed and use at least 78% of the print area without support (or a dedicated build plate if...

The X Axis Chain Retainer Boom is a straightforward device engineered to shield filament from coming into contact with the printer's X Axis chain, particularly in models where the spool is situated above the print bed. ...This boom attaches securely to...

I have not tried Marlin on a stock Anet A8 board, for that I use Skynet3d from https://github.com/thijsk/Skynet3d Marlin 2.0 is now live! I have updated to Marlin 2.0. Autolevel works better and that's all I have noticed! I do run RAMPS. The...

It looks like you've provided a detailed guide on how to install and configure Marlin firmware on an Anet A8 3D printer, specifically for auto-leveling. Here's a summary of the steps: 1. **Define your controller**: `#define...

Hey, I created this "pipe guide" for my Anet A8 which has a cable chain on the X-axis because my filament keeps getting stuck in those chain pieces sometimes. Maybe it will help you too. ... It's designed for the stock extruder of the Anet A8.

This is an upgraded filament guide designed specifically for Anet A8 printers. It seamlessly attaches to the acrylic frame, providing precise alignment with 0.2mm accuracy. ...To ensure optimal results, we recommend printing it diagonally onto the...

This part is untested at this time This is a remix and mashup of the following models: [blindmoe](https://www.thingiverse.com/blindmoe)'s [alternative fan mount/filament guide](https://www.thingiverse.com/thing:2147482)...

... to the nozzle while keeping the mount fixed so it's easy to install and uninstall the caliper. ...I've revised the STL file - check below for updates... I've also integrated a filament guide into the design, and the f3d file is now available too.

I remixed my own Thingiverse design, version 2865844, and incorporated a printed PC4-M6 coupling into version 2 of my reverse bowden adapter. Key upgrades include significantly decreased material needs. ...Additionally, the frame mount no longer clips...

Customized version of https://www.thingiverse.com/thing:2514784 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2514784

I took a couple of other Thingiverse mounts to make this, combining them in creative ways to overcome the problem I had with my chain rubbing against my filament. By piecing together multiple designs, I was able to come up with something that works,...

The foundation for this revised design was somewhat unstable and frequently detached from my printer's frame. This updated version sits lower, slipping smoothly under the spool axle. It also boasts a broader attachment surface to prevent it from...