anet a8 hotbed 3d models
22489 3d models found related to anet a8 hotbed.thingiverse
Made a plug for my Anet A8 hotbed because mine got burned like in picture above. ...
thingiverse
This is a Protection for the hotbed of the Anet A8 or other printers with the Anet A8 hotbed. The springs sometimes caused issues and damaged the hotbeds bottom layer. There have been cases were the hotbed even sparked and caught fire! This fixes the...
thingiverse
... like a little bit unstable. So I made cable holder. It can makes more stable your Anet A8's hotbed cable. 1. You need only a small zip tie. 2. There is no interference with hotbed. (Glass, Pad) 3. Easy to print. ...(No supports, Short time)
myminifactory
A simple spring bushing for the Anet A8 hotbed springs to prevent warping and bending of the springs. By using the OpenSCAD file it can be adjusted so it should be pretty generic. The screw is a tight fit but I find that a good thing for it's...
thingiverse
You can find it at the hardware store for about 5 eur, the sheet is about 70x100 cm and you need a square of about 22x22 cm; some kapton tape glue (every type should work) tools (scissors and cutter) Check out all my Anet A8 projects: Anet A8 Prusa...
thingiverse
This make is for a bracket for mounting a camera to the hotbed of Anet A8 printers. The bracket affixes to the top of the H-bracket, below the actual hotbed. We re-use the holes for the linear bearings and an end clamp to attach the mount to the...
thingiverse
After printing the hotbed stain relief support I really liked the way it was attached to the hotbed and since I was making a short version I though why not just add a handle to the end instead and this is the result. ... The STL is for a single...
thingiverse
Here it is useful and cosy thumbwheel for adjusting hotbed easily and fast. i found really nice this project https://www.thingiverse.com/thing:2350276 but I noticed wheels where too hard to tight. Upgrading this way are now easily to screw. ...Suggested...
myminifactory
You can find it at the hardware store for about 5 eur, the sheet is about 70x100 cm and you need a square of about 22x22 cm;some kapton tapeglue (every type should work)tools (scissors and cutter) Check out all my Anet A8 projects: Anet A8 Prusa i3...
thingiverse
... sideways so it will be easier when I decide for some enclosure. You can see all my notes, recomendations and mods for Anet A8 here: https://www.mikrom.cz/3d-tiskarna-anet-a8/ (it is in Czech, but I am sure you know how to use Google Translator)
thingiverse
A simple replacement for the adjusting nuts that come with the printer. ...Threads in hotbed frame must be removed by drilling. These thumbscrews make levelling much faster and easier. ...No screwdriver will be needed after the installation.
thingiverse
After seeing lots of people having problems with the hotbed connection shorting out over time, and not being able to find anything apart from cable chains that more often than not required turning the bed sideways and soldering wires directly to the...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/gsBiVH8rhRe
thingiverse
This is a hotbed, insulation, and glass holder for Anet A8. It uses standard Anet screws and springs. It takes a 4mm thick glass, 3mm insulation and a standard 3mm Anet 220x220mm hotbed. There are two files. One is a 1/4 piece wich should be printed...
thingiverse
... two corners for best results use 4 corners (4x corner file included). For best results, print in ABS. Will also work in PLA if using a low temperature. Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 100%
thingiverse
Strain Relief for the hotbed cable from the A8. ... Attaches only to two screws of the "H" bed holder.
thingiverse
For Anet A8 orginal springs. Leave the spring centered, avoiding maladjustment when leveling. ... Inner diameter: 3,6mm Outer diameter: 5,5mm
thingiverse
... like this catching on fire and i believe that this mod could help a little bit. If you are using the original Anet`s Auto Leveling Sensor, its a good idea to move it to the front of your hotend, it may hit the cable relief in very large prints.
thingiverse
... the original designer credit! You can print this mount on the Anet A8 as long as you set it 45 degrees on the bed, I printed it on it's side. I am posting this file for individuals that wanted the mount after they saw it in my youtube videos.
thingiverse
These hold down bolts fall outside the 220mm x 220mm ANET A8 build box My final improvement was to add 4mm of cotton wadding insulation purchased off Ebay to the underside of the aluminium heat plate below the heating element. To hold all this in...
thingiverse
Remix of Anet A8 Hotbed Cable Holder by song7070 The changes I made are the distance between the two aluminium plates, this is now 12.2mm. The space between the lips is 3.4mm. ... I also added extra holes so the cable can be fixed with two ty-wraps...
thingiverse
These buhing are designed to fit to spring base shape, in such way that when tightening there is no deformation Print Settings Notes: Layer Thickness 0.1mm Speed 5mm/s
thingiverse
I loved the idea and mount brackets made by aw_ but I wanted to be able to use my go pro accessories and even swap out the camera for my GoPro for a better quality time-lapse when needed. Use the original bed mounts, they work perfectly. I would do...
prusaprinters
<p>These buhing are designed to fit to spring base shape, in such way that when tightening there is no deformation</p> <h3>Print Settings</h3> <p><strong>Notes:</strong></p> <p>Layer Thickness 0.1mm</p> <p>Speed 5mm/s</p> Category: 3D Printer Parts
thingiverse
My first thing, an alternative version of the spring bushing, easier to print. The screws are a snugly fit. ...There is a version with a slope to better support the spring but I am using the ones without.
thingiverse
For Anet A8, printed on Anet A8 @ 0.2mm. ... work on 7mm total thikness (3mm hotbed + 4mm glass).
thingiverse
### Contenido: ### + **holder_hotbed:** * es la pieza completa, separa la cama caliente y H y sujeta el cristal.* + **separador_hotbed:** *es la pieza que separa cama de H, sustituye al muelle.* + **holder cristal:** *es la pieza que sujeta el...