anet a8 plus x belt tensioner 3d models

Made for my Anet A8 but should work for any printer this is printed with a support for the 3.5 mm hole for a screw. only 1 MM thick so it is flexible with PLA. Prints in 5 min or less. Print instructionsCategory: 3D Printer Parts Summary Made for my...

To stop the belt from becoming stuck along its z-axis whenever you tighten the x-belt, take note of this crucial information. ...You won't have to purchase an entirely new belt; instead, simply pay attention to the screw's size, which is M5.

#This project has been discontinued, as I no longer use my Anet A8 and it has since been dismantled ****If you have questions or concerns about the design please post a comment. I will take any feedback and make adjustments accordingly**** The...

This is the stabilizing rod for the main frame of the Anet A8. Print both parts, then put them together and install them as one rod. The diameter of the outer holes are 8mm (M8 screws). 6/9/2017 - Version 2 Like my designs? Support me by buying a...

The Anet A2 Carrier features a block specifically designed to manage the Y-Belt Tension, ensuring precise and smooth operation. ...This versatile carrier also boasts multiple 4mm holes that allow for easy attachment of various accessories or equipment.

Here is the rewritten text: To get started, you'll need a screw, plate, and y-tensioner that are compatible with the y-frame design. ...A great place to find these components is on websites like thingiverse, where users share their creations, such as...

... or ABS plastic (I used PLA instead and still had zero wear). Here are the parts needed: * 2 x 608 bearings (tensioner) * 1 x 40/8mm screw (tensioner) * 4 x 8mm screw nuts * 12 x 3mm screw nuts with lock thread I hope you find this useful, cheers!

Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 20% Notes: print on the side with support for the fan duct, supports are not 100% necessary if you can tolerate some stringing in the fan duct, otherwise...

My A8 wasn't homing properly, so I added an x-stop to adjust when the switch activates. It's not a perfect fit yet and could use some tweaking. ...However, it gets the job done and I'm too laid back to fix something that still works.

List of Customizations: * Centralized pulley perfectly positioned in the middle of the Y plate * Tool-free tension adjustment for seamless operation * M4x30 bolt and M4 nut for added stability * M3 nut slots for convenient access * Reinforced Y...

I created this using tinkercad for the tensioner body, and fusion360 for the block and bolt. ... Edit 07/24/2017: These are the gt2 idler pulleys I'm utilizing: https://www.amazon.com/gp/product/B01H3EY4X4/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

This mount enables you to attach a stock A8 extruder directly to the x-axis. Additionally, it offers a designated spot for installing a cable chain mount. It also includes a location where you can place an M3 screw for securing the Z-limit switch in...

Anet A2 Plus X Motor Holder To prevent the timing belt from rubbing against the axis position of the A2 motor holder, I shifted its alignment. Alternatively, I could have replaced the original parts, but I decided to create a custom solution instead....

Tailored with precision using advanced 3D modeling software!

A crucial assembly demands a specific set of hardware components. Two M4 bolts, measuring 0.7 in length and boasting a diameter of 12mm, are required to secure the system. Additionally, two M3 bolts with a length of 0.5 inches and a diameter of 25mm...

Another cable chain mount for the X-axis, its design is significantly smaller than the original version, allowing the printer to fit perfectly into an IKEA Lack printer table, with added stability. The most crucial aspect is that this new mount...

The housing attaches to the X Carriage upper left bearing via a baseplate, but it only requires three screws. One of the original screws on the bearing is removed and not used, as the longer 18mm screws fit perfectly instead. To secure the...

This mounts to the right side bolts of the X motor bracket on the Z lead screw, leaving room for belt maintenance if you have an open style motor bracket. It's set at a good angle to view prints through the IP camera. You can use this over the...

... hole. This means mine can be installed without having to redo all the cables! I also included the opposite frame brace with my addition. To print this design, you'll need: * 4 x M3 bolts (at least 22mm long) * 2 x M3 bolts (30cm long) * 6 M3 nuts

 Note however, that the belt connector design I incorporated into this carriage is for the classic Anet A8 and as such, the direction of travel on the X axis for an A8 Plus will need to be reversed as the A8 Plus's factory design intends that the X...

V2 is recommended for a better belt tensioning system Hardware Required: --------------------------- * Titan Aero * 23mm pancake stepper * 5015 blower fan * 2 pcs M2 x 10mm bolt (Stock) * 2 pcs M3 nyloc nut * 2 pcs M3 x 12 mm bolt * 1 pc M3 x 35 mm...

This is some small improvements for the y-belt tensioner of the Anet A6 Evolution cube type printer https://www.thingiverse.com/thing:2067818:Guidance to avoid torsion of the beltEnlarged body for using 15mm washers (DIN 9021)The other part...

Humans typically tighten 3 x 15 millimeter screws.

Anet A8 Bear Extruder X Carriage Adapter Power Supply Included are mounts for both the stock power supply and a MeanWell RSP-320-24 I know how you guys love your MeanWells. Credits This project is 75% remixed parts. I will list all the Creators and...

Modified this belt tensioner to work on the DI3 Plus. The belts do not rub or cause issues at either extreme. Installation: To attach the body, you'll need two M4 x 12mm screws and two M4 flat washers. You must screw them into the same place as the...

The thread is slid onto the belt under gentle tension, so that the belt has a slight pre-tensioning. Then, from behind, tighten the nut ring against the hotend carrier. ... I printed it with 1 layer 0.2, then 0.12mm LW 0.38 Nut ring was scaled to 103%

For more up-to-date parts, please go to: ### https://cults3d.com/en/3d-model/tool/ultra-magnus-anet-a8-plus-to-bear-upgrade # Convert your Anet A8 Plus to a big Bear. What is Ultra Magnus? The Ultra Magnus upgrade aims to take the, very...

A component is needed to connect a 10x15mm chain to an X Motor assembly.

I redesigned the x endstop switch assembly to redistribute stress away from the fragile solder connections.

Porta cables para el eje X sin alterar las finales de carrera ni ninguna otra parte.