anet a8 plus 3d models

At approximately 310 hours for the brackets themselves plus whatever it took for the feet, this wasn't a quick project. Assembly took plenty of time as well. This was certainly a 'because I could' project and I had fun seeing it all come together....

If your printer isn't behaving just yet, play around with nozzle and bed distance settings, plus first layer height to find that perfect combination. This is my ABS version; I'm curious to see how other materials perform. If you have any results...

Despite hundreds of Pi-Cam mounting models on Thingiverse, I struggled to find one that worked with my Kossel Linear Plus and the fisheye lens Pi-Cam. So here's my offering to the table, yet another Pi-Cam mount. I'd been experimenting with "Print...

Print enough for the length plus 6 links. - Updated 4/16/2021 Installing this now and found a few small issues. Redesigned the motor plate, motor bearing cap, X mount and switch mount for better fit and alignment. Lots of strength improvements...

Plus, the model is a lot prettier and now much easier to edit (or get machined...). Uploaded f3d and step files for this model (not available for v1.4 since I made that in TinkerCAD).</p><p>The parts I was using for measurements are in far from...

Accessoire pour faire une tresse légère, tresse de cheveux à la mode, outil de tressage, pince à cheveux Magic Curl, pour coiffer des petits pains, pour coiffer, tresse, clip, chignon Ne perdez plus de temps à essayer de trouver de nouvelles...

&nbsp;I added supports just at the edge of battery and GPS recess plus the boom and leash mount. &nbsp;Print time is 1hr 54min for the main body ½ hr for cover and ½ hr for trim and spacers. &nbsp;I have included the Gcode for PETG using a Prusa...

Drop in the holder and secure it from below with the same screws that held the extruder.Notice: It will fit the Qidi X-Plus, X-Maker and I-Mate (S) as well but you must edit the script yourself to fit the bed size.BOM - Bill of MaterialsAll you need...

Extruder: Pitan parts adjusted to fit 5x14x5mm bearings for the hob, and a 4x13x4 grooved bearing on the lever, plus a new 5x14x5mm bearing on the motor shaft for the lever. Optional Pitan body parts with holes for airflow. Suggested to mount with a...

Parts / Terminology - Clamp (klem): the clamp itself, consisting of 2 plates, plus the arm onto which the housing of the camera is mounted. - The housing, which consists of:     - Holder (houder): the bottom part, into which the camera is placed.    ...

On the plus side, that means it will not come out unless you want it to, and will look sleek and mostly flush with the blaster.I have no idea if it will fit on a Nexus Pro. I wouldn't count on it, and it probably wouldn't look good anyways.This...

De plus la face avant ne sera pas trop éclairée de ce fait. Pour l'anneau de diffusion de leds RGB : Hauteur de couche : 0.2mm Périmètres : 3 Remplissage : grille à 30 % ou moins (à adapter à votre convenance) Couches solides basses et hautes : 4...

Plus, you need to remove your tube anyways to get the small chuck of filament out anyways. Better to remote the fitting and be safe.Parts Needed:2x PC4 M10 push release fittings1x 24" PTFE Bowden Tubing (1.9mm ID / 4mm OD)Attach the fittings to the...

Adding a little silicon lubricant makes them work even better.ParametersAll the parameters you need to define are the: outer diameter, inner diameter, bearing thickness, tolerances (the default tolerances should be fine for most cases), mesh...

Pictured is the FDE PETG filament, with TPU for the butt pad.&nbsp;Layer Height: I typically print this with a .3mm layer height.&nbsp;Perimeters/Infill: Doesn't really matter, but I typically print with 2-3 perimeters and 15-20% gyroid...

Replacement Dashboard for a MK3S/S+ to include a Pi 4B and HyperPixel 4 display plus a camera mount. &nbsp;OEM look but way improved functionality!</p><p>I made this probably early 2020 after getting my MK3S. &nbsp;Parts of this design are remixes...

Plus the fan shroud "glows" during the print, which is a pretty cool effect I think.&nbsp;&nbsp; &nbsp; &nbsp;4. Some soldering needed to connect the 3x LEDs in parallel, and route the wires with the main cable bundle to the Einsy board and tapped...

You'll need 4 pairs of pins, each pair adding up to a total length of 0.65", plus a total of 4 keypins: Pairing: Back Pin----Front Pin---Key Pin pin400-------pin250------ keypin400 pin350-------pin300-------keypin350...

60amp ESC https://amzn.to/2PBKRIF 80amp ESC https://amzn.to/38h0tro 120amp ESC https://amzn.to/3qpeObN 150amp ESC https://amzn.to/3sX0toE  Motor 3450kv https://amzn.to/3rsbL3N Motor 3800kv https://amzn.to/2MT6Jyd Motor 2200kv https://amzn.to/2OcaAHc...

It's designed around a Runcam Owl Plus. Not sure what all it'll fit. Throw a comment out with a link to a mechanical drawing of your micro cam and I can see if I can squish it in. For this you need: 2 SG90 servos or equivalent some 3 mm screws: ...

Bill of materials: Eggtracker Mini (only tested with rev C3) Turnigy Nano-Tech Plus 300mAh 2s 70C Lipo Pack (hobbyking, amazon, search around and try not to get raped on shipping) 2 2mm threaded inserts https://www.amazon.com/gp/product/B09MCWX6VV 4...

Plus the can is totally optional and could be swapped with something else like a yellow printed cylinder I have as the hollow can replacement model. You can check out the build video here: https://www.youtube.com/watch?v=AFyLqzJ14Qs Now onto...

O3DS version coming sooner or later.EDIT (11-21-2021): Finalized the 3DSXL design (slightly wider with larger radius fillets inside the slot), changed all meshes to the new CADQuery version, added an MMU SNES-themed model!EDIT (11-22-2021): Updated...

I would recommend using something fairly heat- and water- resistant, as the MM sits outside where it will get wet and will be in sunlight, plus the MM produces its own heat and blows that heat across this canister. I used PETG and that seems to work...

Included with download are the stl files for the 2 magnet holding pieces (print 2 of each), plus the magnet covering caps in two thicknesses, and the central beam.  4 each of the magnet caps are included in the files, the thicker for the 2-magnet...

&nbsp;I'm currently playing death stranding on my PC and came up with the idea of recreating the „Odradek“ scanner as a desk light so I'd like to present you the "Desk Stranding" lamp (thanks to reddit user u/Typh_R who came up with the name).This is...

See the downloaded PDF Plus you need to build the V-core 3 500x500x500 first. Most of the parts, need that big build plate. Hope you enjoy. Best regards Jonas Markussen 6 Update: - The BTT Smart Filament Sensor will now fit inside...

3mm height (plus raft if used). If the design has two color changes required (such as Tears of Joy with white teeth and blue tears) the second filament change is always straight after the top of the first feature (teeth in this example) has finished...

This is not required for the Bambu Lab AMS, but it doesn't hurt adding it.Parts NeededThe Rosahl M-1J1R dehumidifier membrane is available here, same for the USB-C power supply module here.20l storage box: https://www.amazon.de/gp/product/B07P4SC8TQ/...

A Frsky D8RII Plus receiver is connected to these motors in PWM, using one motor per channel, with throttle input provided through the Pitch Stick from the radio. This clever setup allows for simultaneous forward and reverse functions to be...