anet a8 print dimensions 3d models

Based on: https://www.thingiverse.com/thing:2153075/ Because the original didn't fit for my A8, I remixed the files. ...My dimensions are like in the following make: https://www.thingiverse.com/make:377652

First print, picture is of the origional (1/2 size), it didnt get the letters right, i think because some of the settings where for a different printer. started a new one but it ran out of PLA before it go to the letters.... :( Thank you! ...  

If you are just printing this for the Anet A8, you only need the carriage plate, locking levers, and the Anet print head assembly mounting plate. The carriage plate is designed to bolt directly to the bearing blocks on the Anet A8. The locking...

... needs a switch and if the voltage (volts) corresponds to the current supplied by the 3D printer can use it. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Layers Infill: 50or60% Notes: Set PLA 200 degree HotBed 60 degree

These parts are designed to fix the ColorPod on a Anet A8 3d printer. The CororPod converts a reprap style filament 3d printer to a full color powder printer. The ColorPod is a device that extents a regular 3D printer with the capability of...

Anet A8 end print alarm box V1. This is a box to hold the eletronics for a end print alarm. It fit's in a nice and pratical place. Can hold a power switch, a buzzer, four 10mm led, one 5mm led and a push buttom. Have a hole to wires. In my case...

Anet A8 end print alarm box V2. This is a box to hold the eletronics for a end print alarm. It fit's in a nice and pratical place. Can hold two power switch, a buzzer, seven 4mm led and a push buttom. Have a hole to wires. In this version use...

This is a Anet A8 Micrometer height adjuster for the print head .The back half fits directly onto the 3 linear bearing blocks the same as the original aluminium bracket , & uses all original screws for mounting . An adjustable dovetail wedge plate...

And when it's time to free the print, just remove the carbon plate and flex the it slightly to pop off the print. Easy to clean too, just put it in the sink and run the hot water to wash off the glue stick residue. - The cheap china M3 nuts and...

So i dont think its necessary. Anyway i made the new screw with a zero backlash nut. this screw has 1600 steps per mm Print instructionsPrint Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.1 Infill: 20% Notes:...

It is a flat screw you have to print it flat and diagonal on the surface you need http://dkprojects.net/openscad-threads/ to compile the scad files i used candle wax for better gliding the setting is 800 steps per mm I used this screw till christmas...

Remixed version for anet a8 plus metal holder

Test Print. ...Works well for Creality Ender 3.

This mod improved the print quality of my Anet A8 by a lot. I designed this version for low material use (fast print time) and no complex parts. For the assembly, you will need 4 pc-fan-screws 5x10mm Parts I used: Redrex Bowden Extruder:...

... printed circles for a comparison. So even if you level your bed again, as you print along the spool loses weight and your leveling is off again. Well, lesson learned. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 10%

... version has several prints and many hours with no signs of warping. Credit is due to Daniel Levinson. for expanding and testing the updated design. Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 30%

to cover all the wires on the printer anet a8 or other printers-this is a concept to mask the wires be free to modify and share cheers -ryks 10 11 2016 STILL IN DEVELOPMENT \

Found here https://www.amazon.com/gp/product/B00HSF65MC/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 Nothing is needed except some 22 or 24 guage wire (about 58 inches for ANET A8). You can wire directly or include a switch. Or buy the pre-made kit...

(I used a knockoff one and I can run 250 degrees on 0.6mm nozzle with no problem), * It requires 2 side fans so be ready for it, * I am not providing any bowden mount - basically anything will work, so please do your own search and pick the one...

... . The goal was to create a lower profile cooling duct. Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 60-70% Notes: For details on the supports please read through the description

Anet A8

anet a8

A printable alternative does exist (https://www.thingiverse.com/thing:2176224), however I prefer the strength of threaded rod and not wasting so much time printing an upgrade that may be weak. I'm happy to modify for other rod sizes if need be. ... ...

Print in ABS for strength and due to closeness to Hotend, or in PLA should also be OK (images of Purple unit are Not final design, and printed in ABS - later design is slightly thicker and projects slight further forward to give space for the Fan.)...

V2: More secure and substantial hinge, more durable/reliable, better aesthetics, zero-maintenance printed-in supports (still require cut out, but the "stilts" do not require glue to prevent tipping over during printing as they may in V1). Print as...

A 40mm fan adapter with adjustable print fan height and mouthpiece for universal or original nozzle Un adaptateur pour ventilateur de 40mm réglable e hauteur de ventilateur d'impression avec bouche pour buse universel ou d'origine

Yarn transport chain from the card to the print head In use, I lubricated with wd40 once and since then I no longer need it. ... This allows the wires to wear much less because the bending radius is smaller.

I printed the parts for the Hypercube using the hypercube calculator tool from this link: http://superjamie.github.io/hypercube/ and I realized after cutting the extrusion profiles that the provided bed clamps of tech2C did not work. They were too...

This is still in progress, DONT PRINT, use for your modificacion.... Just try to make a better support for connection on the bed and cables. " if you need any file, just ask"" Original project: https://www.thingiverse.com/thing:1875869 ...

After printing a few other things that were 'captive', such as the Gear Gearing (https://www.thingiverse.com/thing:53451) and the Kobayashi Fidget Cube (https://www.thingiverse.com/thing:1790624) successfully, I figured I'd make this cable chain...