anet a8 x belt holder 3d models

You'll need Qty 1: OB 80x20 gantry plate Qty 4: OB wheel kits Screw sets to attach the Anet extruder bracket to the gantry plate The Belt Clamp and Belt Clamp Plate Things. The Clamp Thing includes parts for both left and right side attachment, but...

I'm a stickler for cable management and the Anet A8 was crazy in this regard. I have looked for many Cable Chains, but none of them convinced me; the designs I found were not aesthetically pleasing and others were not compatible with what I was...

Meaning I did not use anyone else's files for the design, but I did reference this thingi, *https://www.thingiverse.com/thing:3462192*, for the design concept, as it was shared to me directly and inspired a real Anet A8 X axis leveler design. All the...

To stop the belt from becoming stuck along its z-axis whenever you tighten the x-belt, take note of this crucial information. ...You won't have to purchase an entirely new belt; instead, simply pay attention to the screw's size, which is M5.

#This project has been discontinued, as I no longer use my Anet A8 and it has since been dismantled ****If you have questions or concerns about the design please post a comment. I will take any feedback and make adjustments accordingly**** The...

This is the stabilizing rod for the main frame of the Anet A8. Print both parts, then put them together and install them as one rod. The diameter of the outer holes are 8mm (M8 screws). 6/9/2017 - Version 2 Like my designs? Support me by buying a...

I found a very old disassembled webcam and decided to mount it onto the XY carriage of my Anet A8 Plus, so I quickly constructed this camera mount, which can be fixed on two or three of the default threadened holes on the backside of the carriage...

My Anet A8 Plus kit was vibrating and shaking on the z-axis when printing, which made me desperate for a solution. While searching online, I stumbled upon @3Displacement's Prusa Bear X Upgrade, which caught my attention immediately. After conducting...

My Anet A8 Plus kit was vibrating and shaking on the z axis when printing. While searching for a solution, I came across @3Displacement 's Prusa Bear X Upgrade which instantly caught my mind. After a few test prints, things where improved but I...

I combined the x-axis rod holder with the motor mount and the belt tensioner, resulting in a reduced width for the printer. You will need a 430mm 2020 V-slot extrusion instead of the original 500mm to accomplish this. I remixed it from another design...

My A8 wasn't homing properly, so I added an x-stop to adjust when the switch activates. It's not a perfect fit yet and could use some tweaking. ...However, it gets the job done and I'm too laid back to fix something that still works.

... belt to your desired level without compromising the alignment of the Z-axis guide rods or screws. This setup also eliminates the need for a longer X-axis belt, as most tensioners that rely on pushing against the X-axis rods would typically require.

This mount enables you to attach a stock A8 extruder directly to the x-axis. Additionally, it offers a designated spot for installing a cable chain mount. It also includes a location where you can place an M3 screw for securing the Z-limit switch in...

This is a modification for the GT2 belt holder on the Prusa i3 A8 Acrylic X Carriage. The original one didn't cut it, but this version works beautifully. To secure the belt in place, use the original screws along with two M4 washers. Additionally,...

Another cable chain mount for the X-axis, its design is significantly smaller than the original version, allowing the printer to fit perfectly into an IKEA Lack printer table, with added stability. The most crucial aspect is that this new mount...

Currently redesigning my Anet A8 Plus and I really liked this simple design for a belt holder, but it wouldn't fit between the bearing blocks I'm using ([thing:1424346](https://www.thingiverse.com/thing:1424346)). ...So I removed the lower mounting...

The housing attaches to the X Carriage upper left bearing via a baseplate, but it only requires three screws. One of the original screws on the bearing is removed and not used, as the longer 18mm screws fit perfectly instead. To secure the...

This mounts to the right side bolts of the X motor bracket on the Z lead screw, leaving room for belt maintenance if you have an open style motor bracket. It's set at a good angle to view prints through the IP camera. You can use this over the...

... hole. This means mine can be installed without having to redo all the cables! I also included the opposite frame brace with my addition. To print this design, you'll need: * 4 x M3 bolts (at least 22mm long) * 2 x M3 bolts (30cm long) * 6 M3 nuts

alternate Sensor holder with more space to access the screws Category: 3D Printer Accessories

Humans typically tighten 3 x 15 millimeter screws.

This is a remix of the belt clamp half of https://www.thingiverse.com/thing:2036499. I printed that part a year ago but it snapped at its weakest point today so I created a thicker body where it was needed. ... The result needed some reaming to fit...

A component is needed to connect a 10x15mm chain to an X Motor assembly.

Porta cables para el eje X sin alterar las finales de carrera ni ninguna otra parte.

In the file it contains: - Two types of chains (open or closed) - Support axis X and Z (female) - Support axis X and Z (male) - Support axis Z and X as well as the limit switch X - Chain support on the extruder - Endstop Z support - Z switch button -...

You'll be able to install your stepper motor for the extruder onto the X-axis using this mounting bracket.

Hi, check out the alpha version of my magnetic x carriage designed specifically for 45 mm spaced x rods. You can watch a demo here: https://youtu.be/i2GAG3h6WsI. This design works seamlessly with cylindrical magnets measuring 14mm by 5.5mm. My...

... or ABS plastic (I used PLA instead and still had zero wear). Here are the parts needed: * 2 x 608 bearings (tensioner) * 1 x 40/8mm screw (tensioner) * 4 x 8mm screw nuts * 12 x 3mm screw nuts with lock thread I hope you find this useful, cheers!

There is an accompanying file, "X_Carrier_Tensioner_V2.stl" which is the part that will hold the idler bearing.While this is not a remix in the classic sense, I did design these to have the look of AVZ's "Anet A8 X Axis Printed Pieces -Idler and...

While this is not a remix in the classic sense, I did design these to have the look of AVZ's "Anet A8 X Axis Printed Pieces -Idler and Motor Holders". A few of the measurements used in my model come from his while others come from the injection...