anet et4x 3d models

The wires on the Pot are a bit flimsy so I would probably recommend sleeving them with some heatshrink tubing before tucking it all into the box. Updated: 04/01/2018 - Thickenend top plate by 1mm for extra strength as I dropped one and the lug broke...

As a newbie, I found it hard getting to change filament; this gate makes it easy, and with practice, if your Anet board allows "Pause Printing," you can change filament color and continue printing - just do it within 30 seconds, so prepare...

Optional Stuff: Anet endstops - https://amzn.to/2KicHWE Screw Assortment* - https://amzn.to/2ZpaJqM Expanding foam glue - https://amzn.to/2X88RW4 *These are used for the electronics, the optional roof and pipe extensions are designed to be used with...

Print Settings Printer Brand: RepRap Printer: Anet A6 Prusa Rafts: No Supports: Yes Resolution: 0.2mm Infill: 15% Notes: Plastic shrinkage is already accounted for in the models, allowing for about 0.2mm to 0.3mm. Project: Headphones Holder Project...

https://www.thingiverse.com/thing:2772648\r\n\r\nMy goal was to make these as compact as possible, able to print on a single bed (which they barely fit on my Anet A8), and still keep them somewhat usable during game night. Finally the standee and...

I was able to print it on a Anet A8 that is wore out and has some issues. Some screws and bolts are needed but over all it is a simple build and easy to print. I uploaded the models in the orientation I printed them and only one piece needs supports...

The Airpods dock is pretty simple, as for the phone stand it's sized for a semi bulky case, making the phone around 11mm thick. While uploading I thought it might be nice to have a "sample" to check if your phone fits before printing the whole thing,...

Solid infill, no supports needed. All printed well (and fast) with 0.6 nozzle at 0.2 layer height. Extra parts needed: 623ZZ bearing (4x10mm, 3mm hole) (may poorly work without) Piece of 1.75mm filament Rubber band Thin plastic bag 6mm silicon pipe...

Holz ist ideal, da es Schwingungen dämpft, aber der CTC Anet Nachbau überzeugte mich nicht. Der Rahmen ist aus 27mm DOKA (Schalungsplatten) recht massiv. Die wenigen Teile zum Drucken sind in PET-G mit einer Layerhöhe von 0,30 und 3,2mm...

Firmware Offsets: x_offset: 28.5 y_offset: 0 Installation: Insert two 6-32 nuts into the mount (for belt tension) Insert two M3 nuts into the mount (for BLTouch) Insert E3D hot end into the mount Install mount and E3D to X-Carriage Install BLTouch...

Connections: pull up RESET (pin 1) with a 4,7k resistor pin 9 to VDD, pin 10 to GND for I2C mode never forget a capacitator with correct polarity between pins 11 and 12, or you'll get display errors, I used 1µF the 47 ohm LED resistor is for VDD =...

The size on the print bed is 114.4x105.3x154 Print instructionsCategory: Computer Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.25mm Infill: 0% Notes: Using Cura 2.3 Mirror one of the two pieces prior to slicing. Shell -wall...

Print Settings: Printer: Anet A8 Rafts: Doesn't Matter Supports: Yes Resolution: 0.1 Notes: To achieve the cleanest top surface, print like a bridge with support material. You may need to sand the inside edges for a smooth fit and drill out mounting...

Works great and do not alter your car. Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.20mm Infill: 20% Notes: I used 20% infill but 2mm thick borders in order to not waste too much plastic for the base, but the thin top...

This is designed to fit the Cecotec Mambo cooking robot, it's used to cover the main jar connectors in order to prevent getting wet when washing, its splash proof, but not waterproof, you can print in PLA or in TPU for best result & fitting (PLA...

Anschließend könnt ihr direkt einen Base Adapter des osVAC Systems (M32) an die Tischkreissäge anschließen. Alternativ lässt sich natürlich auch der angesprochene Winkel noch dazwischen stecken. Links/Details: Allgemeine Infos zum osVAC System:...

Since the board is longer than the one on the Anet, I designed two Cases that can be screwed together. One Case is for mounting the Mosfets at the bottom, and the other one is for the MKS Gen V1.4. As the USB-Slot is positioned in an unusual...

https://www.youtube.com/watch?v=mQ523n6F-xY Check out this link for a step-by-step guide on making your own 3D printed cookie cutters: https://www.instructables.com/id/How-to-Make-Your-Own-3D-Printed-Cookie-Cutters/ The best 3D printer I have is the...

On my Anet A8, the tubes fit the engine and launch lug as they should be. I haven't flown this rocket yet. I will post pictures once it's been flown. UPDATE: I changed the nosecone as I found it fit too snug and I don't want to do a ton of sanding...

**Print Settings:** * Printer: Anet A8 * Rafts: Doesn't Matter * Supports: No * Resolution: 0.4mm * Infill: 30% * Notes: * While a 0.4mm nozzle works fine, using a 0.2mm nozzle is recommended for perfect prints. ... * The space between the upper...

I remixed this when the original creator was kind enough to upload his .f3d file, so I will of course do the same. Just made it a little taller because my USB cord would bend too much with the original design. Tweaked position of back wall hole and...

Required components besides the two printed parts: wrover esp32-cam module two nuts M5 four screws, 60° head, M3x16 (screwed directly into the plastic) For best firmware I found for this module, please refer to this GitHub repository:...

"Mini V linear" (http://www.vslot-europe.com/home/58-mini-v-wheel-plate.html) Je n'ai que ça comme roulement...

I carry my switch with me all the time, but original carrying case has a single pocket for games and joycon straps which makes fetching the game/joycon strap you want a bit hard. I designed a holder which fits in that pocket, can take up to 8 game...

My previous version fits the original Anet A8 filament reel holder and dry box using bought PTFE connectors, but this one takes it up a notch - the entire connector is printed in-house and has worked out incredibly well so far. I use a small piece of...

So the normal type could be good too.&nbsp;I used Gembird PLA, and printed it on my Anet A8 Plus. I set 20% infill. But It doesn't really matter. I think. I uploaded also my .gcode file.</p><h5>FreeCAD file attached</h5><p>This tiny thing could be a...

... you'd like to see in 3D and take the steps leading to manufacture, contact us with any questions or design work you'd like doing. You can reach us via email at sales@quadframesuk.co.uk. 45% discount on the ANET A8 3D Printer Coupon code: A8PRINT

To build this carriage, you will need: 4 x RJ4JP-01-08 drylin bearings 7 x M3x25mm screws (for carriage) 1 x M3x30mm screw (for carriage) 1 x M325mm screw (for extruder mount) 9 x M3 nuts 4 x M3x20mm screws (for front fan) 2 x M4x20 screws (for rear...

Required purchased parts: - Ruthex / igus bearings: https://amzn.to/2H1RAHl - Ruthex M4 threaded inserts: https://amzn.to/32spsmZ - 10xM4 Nuts DIN 934: https://amzn.to/313TGLp Why the use of only igus bearings causes the linear guide to jam:...

MicroSD Extension Cable: LANMU Micro SD to SD Card Extension Cable Adapter Flexible Extender Compatible with Ender 3 Pro/Ender 3/Ender 5/Monoprice Mini 3D Printer/Anet A8 3D Printer/Raspberry Pi/GPS/TV (23.6in/60cm). ... Purchased extension ribbon...