anova sous vide stand 3d models

Just a quick and not perfect remix that fits another model of the Anova Sous Vide with a rounded bottom. ...It does the job though with or without the clamp.

This is a basic stand for the Anova Sous Vide Cooker. Do not leave it in the stand if it is hot. Don't blame me for doing something stupid like that. This is only a stand for AFTER it has cooled down and been cleaned, etc. I didn't have room for...

It fits my Anova Precision Cooker perfectly, even with the screw support on, there is some wiggle room in general on the sides, but I made it so to avoid the stand getting stuck to it. Also, there is a bump on the bottom that fits underneath the...

here is the single with drain hope you like it. ... it fits my Anova and Gramercy Kitchen

I was tired of my immersion cooker laying on the counter so I designed a single stand with a drain. ...got a second cooker and had to redesign it into a double stand

This stand is designed for the Anova Sous Vide Circulator. This allows the device to be secured to the stand and makes for an attractive as well as practical storage solution without taking up space in kitchen drawers or randomly stashed somewhere on...

Remix of DTakehara excellent design to fit the newest model of the Anova Sous-vide cooker. Mine is a bit taller and has a cutaway for the pot clamp. ... Update: Added a version with my logo moved from the bottom to the top/rear of the stand to assist...

A vertical stand for an Anova immersion circulator. This makes it easy to store it upright. It includes a little tray to catch any drips or hold the power cord. The clearances are a bit tight for the stand to fit into the base intentionally - just...

anova sous vide ring for box

anova sous vide ring for box

3D model of the sous vide cooker Anova

This is a collar I use to raise my Anova sous vide cooker so that it doesn't rest on the bottom of my cooler. It's an inch tall, which is perfect for raising it just off the bottom of an Igloo Island Breeze cooler. ...This works with the original lid...

... ... This guard is designed to prevent ice from entering the circulating fan of the sous vide wand. This guard is only to be used in a cold bath. Designed to fit 60mm diameter Anova 2017 Precision Sous Vide wand (This Anova wand is discontinued.)

This bracket is used to adapt the Anova Precise (and possibly other models) to the HOMENOTE Sous Vide Container 12 Quart with Lid & Rack and Sleeve found on Amazon. https://tinyurl.com/y73erxfx The bracket accommodates a 2.30" diameter device.

I wanted to have an insulated top for mounting my Anova Sous Vide while cooking larger cuts for long periods of time. I grabbed a Sketchup model of a Coleman cooler to illustrate what I mean, but using the template you could mount this in any lid. ...

I saw a stand of this design on reddit and thought it could be 3d printed really easy so I whipped up a quick model in F360. Design credit goes to [Reddit user PnickleB](https://www.reddit.com/user/PnickleB). ... This design is untested but I don't...

Simple wall-mount for Anova sous-vide thermostate. ...The fit for the thermostate is very tight though print a bit larger if you want to be sure that it is fitting in the ring.

The blocks allow an Anova Precision sous vide cooker to be securely clamped to the corner of a Lipavi C10 plastic water bath. ... The convex block has a tapered notch that is a sliding fit on the mounting bracket.

As requested by a YouTube Commenter, The 3D printed adaptor ring that holds an Anova Sous Vide cooker in the mouth of a Pepsi Keg, We use this on our overland rig to heat our shower water... ... I printed with ABS or ASA ...

A wall mount for Anova's sous vide cooker. The cooker looks odd on the wall, but I'm short on cupboard space, so the wall had to do. Print Settings Printer Brand: MakerGear ...

Works with the Anova Sous Vide wand, providing a larger "bite" than the factory mount for use on thicker containers. I also managed to maintain the adjustable height feature of the factory mount. One quick note, this does not work well with...

One can be used as a separate support to adjust the height of Anova relative to the water surface. It may be glued to the box cover if wanted. The second version consists of 3 parts. ...One goes below the cover, one in the middle and one on top of the...

This is a modification of abcnj's design, which mounts Anova at a higher point, allowing you to dip Anova deeper into your container. This way you need less water or can allow more evaporation before adding water. The ring will need some bolt and...

This is a reverse engineered replica of the bottom cap for the Anova Precision Cooker found here. https://us.anovaculinary.com/ I recommend that you print this using PETG due to the fact it will be exposed to heat. Supports are not necessary,...

Then I glued the riser part on it with cyanoacrylate glue. For the other version, I also drilled a 62mm hole (and four 5mm mounting holes) and bolted it on the cover of the cooler box. So far have done three of these for family and friends who have...

I didn't like the little rubber tip on the newer style anova clamp so I remixed a extended and widened version. I made 2 version of it, a snap fit that goes directly on the tip of the metal screw and a push fit version that goes over the rubber tip...

Print in PETG or ABS - PLA will become soft once the Anova starts running and things get a bit warm.. Fusion360 file included - feel free to modify yourself :-) Update 20190106 - Lid component added - print with approx. 30% infill. Update...

A stand for a sous vide immersion heater produced by VPCOK. The pictures show a print of the original STL file, after which I discovered that despite all my measuring the bottom of the heater cylinder doesn't rest on the support as intended, and...

The photo has an old version. The model is the updated better version. I really like to original design except how the cord and vents were over the water and the positioning made the machine "backwards" for my use. I also made a ring version...

I needed a new holder for my Anova Sous Vide stick and the original one I designed was intended for wall mounting. ...This one is designed to sit on the side of a regular 25cm pot.