anycubic 4max pro extruder upgrade 3d models
175352 3d models found related to anycubic 4max pro extruder upgrade.thingiverse
Anycubic 4Max Pro great printer, but stock extruder has some issues. I decided to replace it to Titan Aero + Volcano (due to distance between rods and glass near 30mm). ... Updated base v7.3 plus fan duct v3: motor position moved left to set nozzle...
thingiverse
This is a simple open extruder cover to replace the original extruder cover from the Anycubic 4Max Pro 2.0. I had issues with some filaments loosing little chips inside the extruder toothing which I have to clean sometimes. It is annoying to remove...
thingiverse
ABS print. ...4Max pro BMG anycubic. I use the right bmg. You need a hole(blue) in the bmg(yellow) for the bolt(red) for attaching the hotend radiator(black). ... You can install stock plastic (black) mount in BMG
thingiverse
Filament Spool holder for Anycubic 4Max Pro. Mounted on the position of the Filament Sensor and with the same screws and 2 washers. Filament spool holder for 1kg spools with a maximum of 95mm width. V1 is a visually massive construction, but...
thingiverse
Ich habe mir der Filler https://www.thingiverse.com/thing:3020026 für meinen 4Max Pro angepasst. Optimal für 1kg Filamentrollen. ... Über einen Café würde ich mich freuen paypal.me/GeorgAndryk
thingiverse
... for the filament roll holder. You can also print the other version of the holder (Endstück, Stange, Zwischenstück), but i did not test it. Print: 1x Filamentdurchführung 2x Filamenthalterung 4max 3x Rollenhalter_Alustange 2x Endstück_Alustange
cults3d
... core for the filament roll holder. You can also print the other version of the holder (Endstück, Stange, Zwischenstück), but i did not test it. Print: 1x Filamentdurchführung 2x Filamenthalterung 4max 3x Rollenhalter_Alustange 2x Endstück_Alustange
prusaprinters
You can also print the other version of the holder (Endstück, Stange, Zwischenstück), but i did not test it. Print: 1x Filamentdurchführung 2x Filamenthalterung 4max 3x Rollenhalter_Alustange 2x Endstück_Alustange Print Settings Printer Brand: Prusa...
thingiverse
This is a e3d titan extruder mount for the anycubic 4MAX I have uploaded 3 pictures :-) the upper plate have to cut off, shown in the pictures. ... on the side there is hole, you can drill it out for additional mounting from side (i only mounted on...
cults3d
This is a e3d titan extruder mount for the anycubic 4MAX I have uploaded 3 pictures :-) the upper plate have to cut off, shown in the pictures. ...on the side there is hole, you can drill it out for additional mounting from side (i only mounted on the...
thingiverse
This is PRO version of fan duct dedicated to Anycubic 4MAX PRO. ... Easy to print just use ABS and supports from base only.
thingiverse
This is a simple closure for the Anycubic 4Max Pro hood. It's important to use flexible material. ... I have printed this with Recreus Filaflex 82a.
thingiverse
My version of the air ducts for the Anycubic 4Max Pro. The models differ in the air delivery height and the degree of splitting of the jets to flow around the nozzle. ... It is possible to install a protective screen to prevent the cube from cooling by...
thingiverse
Quick Anycubic 4Max pro tool holder I made up since I was tired of constantly trying to hunt down the scraper and tweezers in my part drawer. ... Printed at 0.2mm layer height and 10% infill but the settings don't matter too much unless you're trying to...
prusaprinters
This is a case for the ESP32 Cam to hang inside of an Anycubic 4Max Pro. The Firmware is taken from here: https://github.com/luc-github/ESP3DFrom the GitHub site:This firmware allows not only to have a cheap bridge between Wifi and serial, but...
thingiverse
A cutting tool for the short PTFE tube in the Anycubic 4Max Pro hotend. The original PTFE tube in my printer was too short and caused the filament to collect in the gap between the nozzle and the PTFE tube. Cutting a new piece helped a lot. ...
thingiverse
Hello, in this short video I would like to share with you how I solved the problem of multicolor print using Anycubic 4Max Pro. This printer has it's own firmware based on Marlin however it is not possible to use standard command to change the...
thingiverse
One Part from each remixed Fan Duct joined with tinkercad, to cool the printing part from 2 sides. ... 4Max Pro Duct Mix-3.stl is now the corrected Version. ...The first and second version had litte errors ;)
thingiverse
I have taken one or two measures to save some material, but the holder is so big that it can just be printed on the 4Max Pro, I printed it in EasyABS. the filament sensor must be removed to mount the spulholder, since the screw holes are used. ...
thingiverse
Anycubic 4 Max Pro comes with some tools that allows you to work with, adjust and maintain your machine. ...This part is for persons whom likes order :) There is one extra position, it's for the knife (not included in printers tool set).
thingiverse
It sticked perfectly to the plate and was easy to remove due to bending of the plate • I used a retraction of 0.75 @ 50 mm/s wich turned to fit for most materials (even nylon but not for TPU) Due to the fact, that there is no adequat design to use a...
thingiverse
Appendice manico sportello Anycubic 4max pro
thingiverse
Thi is extended Spool Holder for Anycubic 4Max Pro.
thingiverse
Anycubic 4MAX Pro. ...Замена крышки для фиксации шлейфа.
thingiverse
Vibration damper for 4MAX PRO (ANYCUBIC) TPU 75A When the equipment weighs 15,,,18 kg, the extruder flow is 100...110%, infill - 50% for TPU 75(Shore A). ...
thingiverse
Remix for Anycubic 4Max Pro printer. The 10mm version is 23mm hight. ...
thingiverse
This is a remix of the cooler for Anycubic 4Max Pro. ...I've added two mount points for better stability.