anycubic fan 3d models

This is a fan makeover to match my Titan Aero design. Fits the original holes and bolts of the stroller. The design is lighter and blows the printed material over a larger surface. A project taken from another idea, now I will not find it and...

To enhance the Predator design, a 60mm fan is seamlessly integrated in place of the original stock board-fan. Secure it firmly with either the original screws or double-sided tape for a sturdy hold. ...Experience the power of online editing at...

is a mixed design, the part of the diffuser, is discharged from the network, and added central support to hold two fans, missing a little adjust the dimensions, the fans do not get to enter tube that rework a little housing I haven't tested it 100%...

I'm proud of my DIY design, a stripped-down fan that's both functional and efficient. ...I tweaked its features to perfection and incorporated a convenient wire storage compartment, making it a true masterpiece of innovation.

... to print this part in a high-temperature resistant material like ABS, HIPS, or PC. Printing requires no supports at all. To secure the radial fans in place, use double-sided tape on them and attach them to the original black metal fan holder.

Print Settings Printer: Anycubic Kossel Rafts: Yes Supports: No Resolution: .2 Infill: 30% Notes: I believe I used 2 tops, 2 bottoms, and 3 perimeters. Infill was at 30%, but you might be able to go quite a bit lower. The BL is pretty light, but we...

This fan duct isn't very effective at pushing out a lot of air, so it's best used for printing PETG or ABS parts (I personally use the fan for small ABS prints) and not PLA. I printed it with a .15 layer height using no supports at a slower speed...

Next, simply push the fan into the mounting hole and secure it with some super glue to keep it firmly in place. ...Although the viable space is quite limited owing to the moving effector arms during printing, I've found it works perfectly fine across my...

... the effector using two M2 screws already in place. ... Edits: September 21st Optimizations ensured that the design no longer collides with the arms at all times. September 2nd The height was increased so that the fan would not collide with the arms.

To address this issue, I designed a funnel that connects both the standard 50mm fan and an external 80mm fan. This setup also allows for testing various filter materials and cartridges. The cartridge features a simple "slide on" design. Each...

My New Fan Duct for Predator and 7530 Blowers! I was unable to secure source files for the original design (https://www.thingiverse.com/thing:3790703/files), so I took F360 and created a brand new version from scratch. The blow direction is...

The Fan_Duct _Left is fully compatible with stock part-cooling fans, making it an ideal choice for those looking to enhance their system without sacrificing any performance. In fact, the fan I received as standard didn't fit seamlessly with Renba's...

... with the heat block. ...I specifically designed this upgrade to enhance the fan duct on the Chiron, ensuring it doesn't conflict with the "auto" Level sensor. As a result, it serves as a direct drop-in replacement. ...Try it out and enjoy the benefits!

The internal 50mm fan does not do a great job when it comes to reduce odour. I created a funnel so that the standard 50mm fan AND an external 80mm fan are connected + created a way to test a variety of filter materials and cartridges. ...The cartridge...

A 40x10mm fan rated for 24V operation is also necessary, and modifications must be made to the housing by drilling ventilation holes. The housing should be free of electrical components before drilling the holes. If you find this information...

UPDATE (2023_08_29): noticed that the duct was pointing downward a little because of some interference with the hotend fan. I opened up the side cutaway so it will fit better There didn't seem to be a lot of printable ducts on thingiverse so I...

The outcome was two mounts: - Underfan: as its name suggests, it is intended for mounting under the fan. Settings recommended by 8squarefeet for underfan remain unchanged: X = +36.1 Y = -27.2 Z = -2.1 If you don't want to recompile your firmware,...

Anycubic I3 Mega fan mounting bracket for standard-sized fans.

Made this part to use the Sunon fan (Sunon Radial Fan 50x50x15mm MF50151VX-A99) for part cooling while mounting it in the original Anycubic fan box. Mounting requires a second hole to be drilled right next to the bottom one to fit the different screw...

... 40 millimeter fans with ease. ...It's perfectly suited for cool stepsticks and ramps. To assemble this setup, you'll need the following components: Two forty-millimeter by forty-millimeter fans, two M4 screws and nuts, and four M3 screws and nuts.

Chiron magnetic suction fan This is a fan enclosure restricted to Anycubic Chiron, Why screw it in? Not really, Only two magnets are needed to attach the fan and case to chiron's print head. Very convenient, Remove and install quickly at any...

Replace the noisy PSU fan with a noctua 80x25mm fan. Will require 4 M3x20mm bolts Its a 12V system, just need to cut and connect wiring how ever you like. ... Side cover is very thin to reuse the original hardware, can make it thicker and use any...

IMPORTANT: Use 5V fan in the hotend (tested) The change in this Remix was the I3 Mega for Mega S and other no named With this fan mod you can use two 40x40x10 fans Update Experimental BL Touch ( No Tested ) Plz Give me Feedbacks Update 22/11/20 BL...

Anycubic Chiron 80mm fan duct 80x80

Replacement Cover for Anycubic i3 Mega S Made for 50x50mm fan

Anycubic I3 Mega 40X40 Fan Cover \r\nScythe SY12-4010-L

This replacement fan duct is specifically designed for use on the older model of the Anycubic i3 3D printer, and it can greatly enhance cooling performance.

Removing Internal Build Chamber Ventilation Fan on Anycubic Photon When it's time to replace or remove the internal build chamber ventilation fan in your Anycubic Photon, follow these steps carefully. Step 1: Prepare Your Photon Before starting this...

These components are essential to enable a 120mm fan for air filtration on an Anycubic Photon.\r\nYou will have to buy the 120mm fan and a 90-degree elbow duct, then fill it with activated charcoal.\r\n\r\nI can offer step-by-step instructions if...

Delta Anycubic BLTouch Mount + Fan Duct offers a reliable and convenient solution for installing a BLTouch sensor on your 3D printer's delta configuration, while also providing an efficient way to direct airflow and improve print quality with the...