anycubic mega s auto leveling 3d models

It's held its shape through multiple prints: Anycubic Mega-S Hotend LED Cover Fan Duct Half-Circle: https://www.thingiverse.com/thing:3736680 Alternatively, you can check out Gandalf420's solution here for a different approach:...

It is a cover for the stock extruder for the Anycubic i3 Mega S and Mega X printers (titan clone). It has a small viewport to make it easier to load filament. I liked the idea of this because it didn't seem to have any real downside (I can still...

NOTE: The original Anycubic i3 Mega S belt is slightly thinner than a Gates belt, if so, you will have to fold the belt on itself (with teeth facing outward so it will mesh into the clamp). When you fold it on itself, make sure that a little loop of...

UPDATE: I made the holder slightly wider to give the bearings more space to move freely. I also added a divided roller to glue them together. This Filament roller is for the I3 Mega-S and the upgrade kit. Started remixing and ended recreating it from...

The screwholes allow for some up- and down adjustment to get the perfect height above the part. For mounting the fan to the duct a m3x25 screw and an m3 nut are requried. To mount the fanduct the hotend has to be rotated by 90 degrees so that the...

I designed two different mounting arms, one turned outward for the Mega X and one straight that fits Mega S and Pro. I printed everything with PETG. The holding arms and the roll were printed with 60% infill density and 0.15mm layer height. The...

Anycubic I3 Mega S Z Stop uses a 2.5mm locknut to interact with z stop micro switch. The lack of a sufficient planer surface to interact with micro switch actuation lever causes extreme variation in Z homing resulting in damage to a great work bed...

I made this dual sided fan duct as a slightly improved / better fitting version of the original dual-side fan duct made by H_Run. The original one had some fitment issues on my printer (the fan shroud was too big and too far up). I also changed it...

This is a Remix of the Anycubic i3 Mega-S dual side fan duct by kb-elmo. I liked this design because it matches the sharp lines of the rest of the printer, but it had modeled supports in the duct which blocked airflow a lot. I edited it in...

This is a mount for the Anycubic I3 Mega to apply a Bondtech-extruder (or BMG clones). With the bracket of the original extruder, the filament sensor is not in the right place or it's not possible to attach the BMG. This mounting may work with all...

An extruder and cable guide for the Anycubic Mega S. Meant to keep the cabling / Bowden tube away from the z-axis leadscrew. You'll need 4x 3mm or 4-40 screws, lock and flat washers from your junk drawer. Print using no supports, I used PETG but...

This is a mount for the Anycubic I3 Mega to apply a titan-extruder like with the "original" upgrade-kit. With the bracket of the original extruder, the filament sensor isn't in the right place or it's not possible to attach the titan. This mounting...

Just a very simple bracket to mount a common 60x10MM fan for the mainboard in an Anycubic Mega S. Uses stock hardware locations, clears original stepper drivers. No major disassembly other than removing the bottom plate of the printer is required.

At some point I was not satisfied with a filament spool holder of my Anycubic Mega S - it was too much friction there. So I did a quick design of a simple attachment based on conventional 608 bearings, which are cheap and are used everywhere -...

An extruder and cable guide for the Anycubic Mega S. Meant to keep the cabling / Bowden tube away from the z-axis leadscrew. You'll need 4x 3mm or 4-40 screws, lock and flat washers from your junk drawer. Print using no supports, I used PETG but...

Ongoing project to integrate MKS Tinybee into my Anycubic Mega S. The mainboard mount is complete, now fiddling with the firmware. Note that Tinybee has only 4 endstops, so I forgo the filament runout sensor, keeping X, Y, and dual Z. I have the...

I designed this X-axis belt tensioner to fit onto an Anycubic i3 Mega S because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with no modifications necessary to the current fixture. No need to...

...... I designed this **X-axis belt tensioner** to fit onto an **Anycubic i3 Mega S** because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with **no modifications necessary** to the current fixture.

Here's my revised half-circle version for the Mega-S: https://www.thingiverse.com/thing:3733579 And here's my updated half-circle hotend cover version for the Mega-S: https://www.thingiverse.com/thing:3736680 EDIT: I added an updated version with...

Hi all, I've remixed the original cable shroud and added the Mega S logo to the hotend cover's front face. I also added the blank version without the letter "S" for other Mega series users can customize it. You can use a double sided tape to...

The filament end sensor as installed on the Anycubic i3 Mega S is a bit of a problem. The filament is always pulled from the inner side of the spool which can lead to jumping filament when it comes from the outer side. These cracking noises are worse...

I found some mounts for Mellow's BMG Aero and Anycubic i3 Mega (S) but all of them was a bit disappointing. So I created one myself. With drag chains, LED light, integrated X belt tensioner an so on. I tried to use as much stock components as I can...

Dadurch sollte sich das PSU kältere Luft durch die seitlichen Löscher und nicht die warme ziehen. Dazu habe ich noch ein paar Wände schmaler gemacht (eher schnell und unsauber), dadurch sollte man etwas Zeit und Material sparen. Hoffentlich klappt...

I'm not pleased with these calibration tests - they're all too complicated! Most have nine different components, which seems excessive to me; five would suffice. ...To simplify things and save time, I've streamlined the process, particularly for those...

Very rarely I have to adjust the table, so I constantly forget which way to turn. Therefore, I made handles with direction, which are simply put on the original ones. No unnecessary glue or other tricks. This is a remix, only more processed,...

This is a remix of some models found in several 3d websites, but designed from scratch in Freecad.The model was resized so that it fits very tightly to the original knobs, and assembly is only possible by tightening the two pieces in a vice.I got...

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

Couldn't find a cable holder that i liked so made my own. ...this fits my mega pro but should fit the s. ...It's bolted to the bottom slide plate and is solid and takes all the pressure of the solder points on the heat bed.