anycubic mega s upgrade 3d models

An extruder and cable guide for the Anycubic Mega S. Meant to keep the cabling / Bowden tube away from the z-axis leadscrew. You'll need 4x 3mm or 4-40 screws, lock and flat washers from your junk drawer. Print using no supports, I used PETG but...

I made this dual sided fan duct as a slightly improved / better fitting version of the original dual-side fan duct made by H_Run. The original one had some fitment issues on my printer (the fan shroud was too big and too far up). I also changed it...

At some point I was not satisfied with a filament spool holder of my Anycubic Mega S - it was too much friction there. So I did a quick design of a simple attachment based on conventional 608 bearings, which are cheap and are used everywhere -...

Just a very simple bracket to mount a common 60x10MM fan for the mainboard in an Anycubic Mega S. Uses stock hardware locations, clears original stepper drivers. No major disassembly other than removing the bottom plate of the printer is required.

Ongoing project to integrate MKS Tinybee into my Anycubic Mega S. The mainboard mount is complete, now fiddling with the firmware. Note that Tinybee has only 4 endstops, so I forgo the filament runout sensor, keeping X, Y, and dual Z. I have the...

There should be no interference problems now, assemble onto the existing fan bracket and it should work fine.Things you'll need:2pc 50mm x 50mm x 10mm fans 12V (can search for 5010 fans online)1pc Y cable XH2.54 female to 2x XH2.54 male (to use power...

Here's my revised half-circle version for the Mega-S: https://www.thingiverse.com/thing:3733579 And here's my updated half-circle hotend cover version for the Mega-S: https://www.thingiverse.com/thing:3736680 EDIT: I added an updated version with...

Hi all, I've remixed the original cable shroud and added the Mega S logo to the hotend cover's front face. I also added the blank version without the letter "S" for other Mega series users can customize it. You can use a double sided tape to...

I found some mounts for Mellow's BMG Aero and Anycubic i3 Mega (S) but all of them was a bit disappointing. So I created one myself. With drag chains, LED light, integrated X belt tensioner an so on. I tried to use as much stock components as I can...

The filament end sensor as installed on the Anycubic i3 Mega S is a bit of a problem. The filament is always pulled from the inner side of the spool which can lead to jumping filament when it comes from the outer side. These cracking noises are worse...

Dadurch sollte sich das PSU kältere Luft durch die seitlichen Löscher und nicht die warme ziehen. Dazu habe ich noch ein paar Wände schmaler gemacht (eher schnell und unsauber), dadurch sollte man etwas Zeit und Material sparen. Hoffentlich klappt...

Couldn't find a cable holder that i liked so made my own. ...this fits my mega pro but should fit the s. ...It's bolted to the bottom slide plate and is solid and takes all the pressure of the solder points on the heat bed.

This X-Axis Linear Rail Upgrade is designed for use with my Orbiter Direct Drive System: https://www.thingiverse.com/thing:4856555 This uses an MGN12H with 300mm Rail. A neat feature for Klipper users is the dedicated ADXL345 accelerometer mount....

This is a remix of "dkcwenge" design of fan duct for Mega-S i've changed the connection holes, so a noctua Fan (40x10 or 40x20) would fit without screws now ;) Thank you for providing the step files ;) i've printed it with tree support, the only...

DIY Camera Mount Kit for Anycubic S Pi Cam Featuring a Customizable Spool Holder Design Looking to capture stunning footage with your Anycubic S Pi Cam? Look no further! Our camera holder kit is designed specifically for this popular camera model,...

Anycubic i3 Mega S Y-Carriage Belt Tensioner UPDATE: Added a Carriage_mk2 file which features a slightly sturdier back. I noticed after a year of use and perhaps slight over-tensioning on my part, the screw that pulls the carriage back has started...

... I have created a smaller version to fit the right-front corner and the back-center. A M3-.50 nut is required. I tried the Drag Chain of RTamer, but the connector didnt work for the i3 mega s, so I added this thing to get it done directly.

...... I designed this **X-axis belt tensioner** to fit onto an **Anycubic i3 Mega S** because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with **no modifications necessary** to the current fixture.

I designed this X-axis belt tensioner to fit onto an Anycubic i3 Mega S because there isn't one that I could find readily available on here. You can install this onto a stock Ai3MS with no modifications necessary to the current fixture. No need to...

Das ist eine Halterung für den Anycubic I3 Mega um einen Bondtech-Extruder (oder einen BMG-Klon) montieren zu können. Mit dem Halter des originalen Extruders passt die Ausrichtung zum Filamentsensor nicht mehr, der Extruder steht seitlich über oder...

Spool Holder - Nice & easy improvement for Any*cubic (i3 Mega S/Pro) English: With this spool holder the filament simply rolls softer, because the holder now has a round surface. The roll does not jump off anymore and filament is transported better....

Snaps around the frame of a Mega-S. This might not fit depending on how you have your filament sensor set up. I don't use mine, so it's not an issue. Would be easy to adjust in TinkerCAD which is all I used. I've found that the long side is a little...

I upgraded TechDayEveryDay's top knobs with added directional cues, giving users instant feedback on their input settings. ...To achieve this, I first printed the knobs in crisp white and then employed a precise black Sharpie to carefully fill in the...

Inspired by stories how amazing direct drives could be I decided to remake my i3 Mega-S ('S' is very important here, latelly you will understand why) I went across lots of amazing projects and even printed one based on Philipp's guide...

Hopefully lasts. Print Settings Printer Brand: Anycubic Printer: All-metal Mega Rafts: Doesn't Matter Supports: Yes Resolution: 0.15 - 0.2 Infill: 20 Filament: Redline PLA with non-abrasive aluminium Eisengrau Glitzer Notes: Use supports from...

The "Back Right" versions are because I have a bed cable guide installed (modified because the gap was too thin for my Mega S, original is in the "remixed from" list and modified version is in files), and the normal versions didn't fit. They might...

My mounting part is only compatible with the "Mega S" due to its reliance on the original metal filament holder as the mounting surface. Screw holes for fan attachment are approximately 4mm in diameter, making it simple to create threads without...

Yet another take on part cooling fan improvement for the i3 Mega S. This design uses the existing fan and carriage and allows for cooling from both sides. I performed a bit of CFD to help ensure airflow doesn't hit the nozzle, as much as possible. I...

It fits the original Anycubic "BOOSFAN JD4512M12" fan and any 40 x 10 mm fan used for extruder cooling, which in my case is the Noctua NF-A4x10 FLX. The Noctua NF-A4x10 FLX fan operates at 12V, not 5V. You can find it on Amazon DE at...

This is a heat-gun base/holder that can be clipped onto the top of the Mega (S) frame. It's intended to be paired with some kind of shroud (like a sturdy heat-resistant bag, or chamber) to create a heated environment. A heated environment will make...