anycubic photon stl files 3d models

These files can be printed out and used to create a leak-free exhaust system for the Anycubic Photon. This is in contrast to an existing backplate replacement with a 4" duct attachment, which misses fumes that exit at the bottom of the printer or...

... on Thingiverse. Click this link to become part of the Photon Army: https://www.thingiverse.com/groups/anycubic-photon Watch this video for step-by-step instructions on how to clean your resin vat after printing: https://youtu.be/-9aPhhMv4ww

This STL is an 8-up copy of the Photonsters Resin Exposure Test v2 arranged for use with the Anycubic Photon M3 Plus.  Here's what I've done:Subdivided the 197mm x 122mm build platform into 8 equal sectionsScaled the original STL by 95% so it...

I split the complete pod into Tinkercad and sliced it down the middle so that each half would fit on the AnyCubic Photon build plate. It should also fit on similar sized resin printers, such as the Elegoo Mars, Epax X1 and Longer Orange. You will...

Anycubic Photon Side Panel 4-Inch Extraction Tube Adapter. ...The diameter has been upgraded to 9.6 inches for a more precise fit.

I neded a holder for all the tools of my 3D printers (Anycubic predator, photon zero). So I designed one in Fusion360. ... Feel free to use.

I upgraded my Anycubic Photon Mono SE with Solvo magnetic buildplate. ...So i needed this spacer to save my screen from crashing.

A low profile angled fan mount for the rear of the Anycubic Photon S. ...Allows mounting a 120mm fan and wire passthrough.

Anycubic Photon S Drip Hanger Pro instead of an axis in the loops, you can put a piece of filament and glue it with glue

I modified the original vat holder to accommodate the Anycubic Photon Mono X. ... Fit's nicely and does what it was designed to do.

This flag is a replacement flag instead of using a spacer and longer screws when using a flex plate on the Anycubic Photon Mono X 6K.

Unfortunately, after the firmware update (https://www.anycubic.com/pages/photon-mono-4k-firmware-upgrade) PM4K_F014.bin | PM4K_V_202.bin changed the alignment and order of the test, which is why the original test file can no longer be used. The new...

... function at its best, it demands a precise distance to pull up the screen into its flat position. ...A notable height discrepancy exists between the original LCD screen on the Anycubic Photon S and the Elegoo Mars screen, measuring between 0.7-0.8mm.

A slight tweak was implemented, eliminating the floating clip to facilitate easier printout access. ...Additionally, dual extruder files have been crafted with intentional support designs specifically intended for use alongside raft features.

Happy printing :-)) other Photon projects https://cults3d.com/en/creations/anycubic-photon-s-adjustable-height-foot https://cults3d.com/en/3d-model/tool/vat-drip-off-holder-using-20-x-20-profile...

Sadly the anycubic photon doesn't come with metal for the suggested magnetic mounting from Photonsters. However, if you change 2 of the bolts supporting the Z axis to slightly longer screws the supplied mount will allow you to install the PTC heater...

This adapter will work with most 90mm square box fans, adapting to 3 inch duct. ...This is designed to be printed on an Anycubic Photon printer.  I suggest using ABS resin and no scaling.

I am testing a custom-made prototype to gauge its ability to accurately print hair-like filaments with an AnyCubic Photon 3D printer, specifically utilizing the Tenacious flexible resin for optimal results.

fast design resin screw and antenna protection - Anycubic Photon Mono X - not need support - infill 15% before instal this protection need unscrew antena - no need to glue. ...The guard clicks into place behind two small screws on the top plate.

This is a replacement knob for the Vat of the Anycubic Photon Mono X. It's designed to accept the bolt from the factory knobs. ...Just break off the remaining degraded plastic and the bolt should slide into the knob.

This is a spacer that can be used on the Anycubic Photon Mono to move the z limit trigger down 2.6mm. Alternately you can use 2 small washers. ...

Adds +5mm to the Anycubic Photon M3 Premium z-axis arm. Rests on the arm, can be glued or taped. Works well with the Wham Bam flexible build system. ...

I made a adapter for Anycubic Photon Zero to the Elegoo Mercury Plus. ...Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 200 Infill: 10 Filament: ESun PLA Category: 3D Printer Parts

Here is a 3mm longer "blade" so you can use the wham bam system on your anycubic photon mono X 6K. ... you just have to reuse the existing screws.

I designed this part to connect my Anycubic Photon to my apartments ventilation system to get rid of the resin fumes. It takes a 120-125mm flexible tube. Photo's will follow later. ... Category: 3D Printing

Anycubic Photon Mono X 6k Dripping Bracket with Resin Wringer Printer brand: Creality Printer: CR10S Pro V2 Rafts: No Supports: Yes Resolution: 0,20 Infill: 40% Filament material: PETG

Join The Photon Army Today and Get Access to Exclusive Content, Tips, and Support from Fellow Enthusiasts at Thingiverse. ... Watch This Step-by-Step Guide on How to Replace the Mainboard of Your Anycubic Photon 3D Printer: https://youtu.be/m1LD5Upl6eA

Here you find an upgrade for the Z axis of the Anycubic photon. My own Z axis never worked properly, plagued by annoying Z wobbles. I discovered a straightforward solution without resorting to drilling or CNC parts - just some glue and 3D printed...

A simple set of spacers which, when installed, raises the Z axis homing height on the Anycubic Photon Mono. This is particularly useful if installing a magnetic build plate as I found the Sovol plate made Z axis adjustment impossible. I have...

DIY Wash Station for Anycubic Photon / Photon S Create a bracket to hold the photon plate on top of a food box lid, filled with IPA that's being agitated by a magnetic stirrer. A second lid is needed to close the box after the wash cycle is...