anycubic vyper change filament during print 3d models

Printed on Anycubic Vyper

Workstation: Easily change your filament, keep it stored ready for use, dry, warm and untangled. Wooden (MDF) cabinet with heater consisting of 2 resistors, fuse and a thermostat. Added a dehumidifier. Filament ready on 10mm rods with (nylon)...

Check out this tutorial here and learn how to turn any shape into a printable model: https://www.youtube.com/watch?v=KsbE2vEzS7U Most printers support the M600 command, which lets you change filament during printing. You can use different colors for...

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

Design optimized for FDM 3D printing. ...It's an adapter to use Anycubic filament spoolers into 8mm Prusa/ Grabber i3 rods.Requires 2 bearings 608Z or similar.

Is a free copy of the Anycubic I3 mega upgrade to mega S spool-filament holder. ...The print needs 25% infill, 35 mm/s, and 0.3 resolution.

This is a file for a filament sensor mount on the Anycubic Mega X. It is meant to replace the factory mount in case that it is damaged or missing. ... Can be printed via Resin or Filament.

...Then with front plate use the 'pause and change filament' option on whatever the first layer ABOVE the base layer (where the text starts is the change point, it's layer 9 for me). Start with white, change to red. The back as space for 10mm LEDs.

Then with front plate use the 'pause and change filament' option on whatever the first layer ABOVE the base layer (where the text starts is the change point, it's layer 9 for me). Start with white, change to red. The back as space for 10mm LEDs. If...

... the screws' positions by removing them from their original slots and then insert them into the corresponding holes on the spool holder. This will provide a snug fit for your filament, keeping it organized and within reach during printing sessions.

A simple remix to print the token in 2 colors with a Filament Change at layer 20.

Bubbles can become a problem during printing. Instructions: From the start, I decided to utilize the extruder driver to move the syringe plunger. However, this led to the first challenge: the extruder's built-in safety feature prevents it from...

... insert for 1.75mm filament, though it hasn't been tested yet. To make the process easier, print multiple small inserts; place the first one at the bottom of the body, as shown in the photo. ...Using a Dremel tool on the insert was crucial for me.

Adapter mod for the adapter of the shifter knob to make it easy to use. ...You only have to apply preassure to put the knob in. It also let's you change it when u want. PRINT HORIZONTALLY OR IT COULD NOT MAKE THE PREASSURE IT NEEDS TO FIT CORRECTLY.

Another extruder designed for printing flexible filament on the Anycubic i3 Mega comes equipped with 4mm PTFE tube requirements. Only about 20-25mm is needed to get started. The original silver collet is reused, allowing users to install it with an...

Yet another extruder for printing flexible filament on the Anycubic i3 Mega is designed specifically to be used with 4mm PTFE tube, requiring only about 20-25mm. The original silver collet can be reused after installing it with an M6 nut or my...

To assemble this guide, you'll need: * 1x M3 15 mm screw * 1x M3 washer * An 8 cm filament tube (such as a standard 1.75 mm tube available on Amazon) Cut the tube using a sharp knife or carpet cutter, taking care not to compress or deform it during...

Filament holder for anycubic 4 max pro 2.0, 4 max dual and so on.

a filament spool holder adapter for my anycubic mega pro for less friction on the spool.

A filament runout sensor mount for the Anycubic Kobra and lack enclosure.

While looking at https://www.thingiverse.com/thing:4966317 I wanted to recreate the entire drawer, so that I could squeeze even more use out of the space :) So far this has resulted in this model, the magnet slots in the back has been replaced with...

Human Made Device: Weighs a mere 54.75 grams, equivalent to a compact 0.121 pounds.\nDimensioned at 151.4mm (5.96") in length, 88.9mm (3.50") in width and a slender 23.4mm (0.92") in depth.\nThe machine's high resolution is precisely calibrated to...

Anycubic Vyper Stilts. ...(Legs) (Feet) (Risers)

Functionality Details: A total of five hundred thirty-one minutes plus one additional minute are taken for print time requirements during production cycles as indicated by project specifications prior completion confirmation once fully assembled...

Customized version of https://www.thingiverse.com/thing:5640914 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5640914

My First Design on Tinkercad

I'm glad you liked it! I'd be happy to help if you need anything. ...You can also support me through PayPal at www.paypal.me/TFenk.

PLA 1.75 - 220. I required it slightly thicker and a mechanism to secure the bearing in place. Therefore, I incorporated an M8 and nut, modifying the mount to accommodate the bolt. ...This modification proved effective thanks to MadManic's expertise.

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069