baofeng volume knob 3d models

This Knob is design to replace the original one on the UV5r And UV82. ... Is bigger size allow easier manipulation with gloves A hole for a small M3 headless screw allow you to secure it in place (not mandatory)

Check the diameter of your antenna/connector and pick the appropriate size I have only printed both knobs in TPE. Have not checked fitment with other materials. V0 should work for PLA or the likes, It exactly matches the original on the shaft size....

A simple antenna-mounted knob cover for a Baofeng radio. Has only been tested on a UV-5r. Excellent little add-on to avoid accidentally turning your radio on or off. Print it with the honeycomb pattern on the build plate. The cover snap fits on...

For assembly, you will need a dab of glue (I might recommend a little white craft glue), for the Locking Seat, then install the Locking Knob, then finally the Locking Pin (maybe another dab of glue). If you used craft glue, you should be able to...

This is a two-way ham radio volume knob. It is suitable for a baofeng style radio. I made it specifically for a Quensheng UV-R50 and a Baofeng BF-UVB2-Plus radios. It should hopefully fit other models and radio. It was inspired by the movie...

This piece fits over the volume/on knob at the top of a Baofeng UV5R ham radio and prevents it from rotating further. It is a snug slip fit and is a finicky piece to design with all the small detail. However this is really useful if you put the...

Just a neat volume knob for Baofeng portable radios. SolidWorks source file included as well, so you can parametrize it for your needs. Simplify3D factory file included too. ... / UR6LKW, 73!

Fits Baofeng UV-5R Volume knob. Customized version of http://www.thingiverse.com/thing:41274 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=41274 Instructions Using the following options:...

My take on a volume knob, inspired by https://www.thingiverse.com/thing:1683431 I like this one a little better than the stock one, and I think the knurling feels nice, so maybe give it a try if you like the look Volume Knob has rounded edges while...

I don't like the huge and ugly original volume knob. So I drew one by taking a look at the UV-9R Plus one. It also features a reference notch.To be printed with flex or semiflex filament, tipically TPU it's a good choice.You can choose to print and...

I don't like the huge and ugly original volume knob. So I drew one by taking a look at the UV-9R Plus one. It also features a reference notch. To be printed with flex or semiflex filament, tipically TPU it's a good choice. You can choose to print...

I don't like the huge and ugly original volume knob. So I drew one by taking a look at the UV-9R Plus one. ...It also features a reference notch. To be printed with flex or semiflex filament, tipically TPU it's a good choice. You can choose to print and...

Volume knob cover for a Baofeng UV-5R ham radio. - Prevents accidental turning of the volume knob - Has a light shield to prevent side bleed from the LED light. Print - Print solid with all perimeters, no infill. Assembly - Glue in place with...

Small friction fit protector that slides down over the antenna of a standard Baofeng UV-5R. ...Protects the volume know once set so it cannot be bumped or turned when in a pocket or pouch.

A replacement power / volume dial for the Baofeng UV-5R.

Added cuts in volume knob protector for easier access to adjust. Added cut in PTT protector so it can still be used, but not easily bumped accidentally. Rounded corners for more comfortable handling. This design uses existing screws with the...

Who has one of these Radio devices knows how easily you can loose the knob. ...I was using the device without a knob for almost a year, until i designed this knob. ... Enjoy!

While there is quite a lot of overhang underneath the knob, its so small that support material is not too big a challenge.

I made a simple clip-in volume knob cover for my Baofeng UV-5R, so that it wouldn't turn on when carrying it around.

Customized version of https://www.thingiverse.com/thing:168277 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=168277

This remix tweaked a few characteristics to fit the Baofeng BF-F9 V2+ & thinned it out a bit. I test fitted to a UV5R & still works on it aswell. *Please donate every design takes hours. ...Thank You :)*

The default radio knob seemed to constantly change when worn on a buoyancy aid - therefore I created a sleeker, and less snagable replacement. ...

I lost the knob of Baofeng GT-3. ...So I designed a new one and print it.

I used this to keep in place volume output that I was sending to a "mic input" and without it a small movement of knob caused huge changes in mic gain. Now it is pinned and I can use an audio mixer to set the "mic in" precisely. ...The project is a APRS...

They should fit any Baofenghttp://www.amateurradiosupplies.com/v/vspfiles/photos/UV-5R-2T.jpg VolumeCover: Stops your volume knob from being accidentally bumped during carry, or when in your pouch. The cover has slits so you can still change the...

They should fit any Baofenghttp://www.amateurradiosupplies.com/v/vspfiles/photos/UV-5R-2T.jpg VolumeCover: Stops your volume knob from being accidentally bumped during carry, or when in your pouch. The cover has slits so you can still change the...

Volume knob

Desktop volume knob

Mount volume control for AIRSOFT, hunting and others. ...Removes accidental increase / decrease in volume. ... infill 50-100% layer height 0.2

A protective cap to avoid unintended volume change or turn on/off. ... Need some filing to fit the LED and battry snap, glued mie with verry little hot glue.