baofeng volume lock 3d models
77041 3d models found related to baofeng volume lock.thingiverse
I used this to keep in place volume output that I was sending to a "mic input" and without it a small movement of knob caused huge changes in mic gain. Now it is pinned and I can use an audio mixer to set the "mic in" precisely. ...The project is a APRS...
thingiverse
For assembly, you will need a dab of glue (I might recommend a little white craft glue), for the Locking Seat, then install the Locking Knob, then finally the Locking Pin (maybe another dab of glue). If you used craft glue, you should be able to...
thingiverse
A protective cap to avoid unintended volume change or turn on/off. ... Need some filing to fit the LED and battry snap, glued mie with verry little hot glue.
thingiverse
I wanted a simple volume locking knob for my Baofeng, this is a remix from https://youtu.be/R0yv_Sj9CwI - dont know if he designed it but i adjusted his which can be found in the description text of the video in a dropbox link. The original was...
thingiverse
The original design was a bit too tight on the antenna I used and I felt the connecting arm was a bit weak as mine snapped of when pushed in place. ... Changed the inner diameter of the antenna hole and redesigned the connecting arm to be stronger.
thingiverse
I made it specifically for a Quensheng UV-R50 and a Baofeng BF-UVB2-Plus radios. It should hopefully fit other models and radio. It was inspired by the movie Terminator. Special Thanks to the following below for making great models I could remix...
cults3d
They should fit any Baofenghttp://www.amateurradiosupplies.com/v/vspfiles/photos/UV-5R-2T.jpg VolumeCover: Stops your volume knob from being accidentally bumped during carry, or when in your pouch. The cover has slits so you can still change the...
cults3d
This piece fits over the volume/on knob at the top of a Baofeng UV5R ham radio and prevents it from rotating further. It is a snug slip fit and is a finicky piece to design with all the small detail. However this is really useful if you put the...
thingiverse
They should fit any Baofenghttp://www.amateurradiosupplies.com/v/vspfiles/photos/UV-5R-2T.jpg VolumeCover: Stops your volume knob from being accidentally bumped during carry, or when in your pouch. The cover has slits so you can still change the...
thingiverse
Fits Baofeng UV-5R Volume knob. Customized version of http://www.thingiverse.com/thing:41274 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=41274 Instructions...
thingiverse
Mount volume control for AIRSOFT, hunting and others. ...Removes accidental increase / decrease in volume. ... infill 50-100% layer height 0.2
thingiverse
My take on a volume knob, inspired by https://www.thingiverse.com/thing:1683431 I like this one a little better than the stock one, and I think the knurling feels nice, so maybe give it a try if you like the look Volume Knob has rounded edges while...
thingiverse
I keep accidentally adjusting my volume on my radio and I didn't quite like the options already on here, so here we are. Both parts are intended to be printed with TPE/TPU. The knob is just slightly taller and skinner than the original, but only...
thingiverse
I don't like the huge and ugly original volume knob. So I drew one by taking a look at the UV-9R Plus one. It also features a reference notch. To be printed with flex or semiflex filament, tipically TPU it's a good choice. You can choose to print...
myminifactory
I don't like the huge and ugly original volume knob. So I drew one by taking a look at the UV-9R Plus one. It also features a reference notch.To be printed with flex or semiflex filament, tipically TPU it's a good choice.You can choose to print and...
prusaprinters
I don't like the huge and ugly original volume knob. So I drew one by taking a look at the UV-9R Plus one. ...It also features a reference notch.<br/> To be printed with flex or semiflex filament, tipically TPU it's a good choice.<br/> You can choose...
thingiverse
Made a slight modification to the Baofeng battery lock. Original one seemed to be a little off. Push part of the lock clip was smaller than the original manufactured clip so I made that a little bigger, as well as the bottom wedge. Made the bottom...
thingiverse
A replacement power / volume dial for the Baofeng UV-5R.
cults3d
this was designed to protect the ptt and volume knob on a baofeng uv5r to stop the knob being pushed and hot micing the radio ptt
thingiverse
I made a simple clip-in volume knob cover for my Baofeng UV-5R, so that it wouldn't turn on when carrying it around.
cults3d
Small friction fit protector that slides down over the antenna of a standard Baofeng UV-5R. ...Protects the volume know once set so it cannot be bumped or turned when in a pocket or pouch.
thingiverse
Volume knob cover for a Baofeng UV-5R ham radio. - Prevents accidental turning of the volume knob - Has a light shield to prevent side bleed from the LED light. Print - Print solid with all perimeters, no infill. Assembly - Glue in place with...
thingiverse
... on the build plate. The cover snap fits on the antenna shown in the picture that comes with SOME Baofeng radios. ...If your antenna doesn't have the lines at the very bottom, refer to my profile for another model that will friction fit onto it.
prusaprinters
<p>I have seen others like this but nothing worked like I wanted. ...This will protect the PTT & Volume from unwanted activation & adjustments. ...Great if you need the radio to be in a pouch or pocket. </p>
thingiverse
I remixed it to just include the volume portion and rounded it off a bit. Screws should be M2.5X10mm Spring loaded belt clip can still be used Fusion 360 file Included if you want to adjust 5 or 6 trials later I have it pretty tight and...
thingiverse
Added cuts in volume knob protector for easier access to adjust. Added cut in PTT protector so it can still be used, but not easily bumped accidentally. Rounded corners for more comfortable handling. This design uses existing screws with the...
thingiverse
Spare battery lock. ...The axis of rotation was reinforced with an attache.
prusaprinters
I had broken my radio's battery lock mechanism. ...I modeled a new one and it fit perfectly.</p>