battery for redcat gen 8 3d models
2485390 3d models found related to battery for redcat gen 8.thingiverse
This is a sideways battery conversion for the Redcat Gen 8 International Harvester Scout II scale crawler. This conversion allows you to get the weight bias quite a bit more forward. For fine tuning, there are many different combinations of screw...
thingiverse
This is a sideways battery conversion for the Redcat Gen 8 International Harvester Scout II scale crawler. This conversion allows you to get the weight bias quite a bit more forward. For fine tuning, there are many different combinations of screw...
thingiverse
This is a rear (shorty) battery conversion for the Redcat Gen 8 International Harvester Scout II scale crawler. It was created to help get the battery away from the cockpit area, for anyone who wants to go "full-scale" and needs more room for...
thingiverse
Designed for use with Redcats rear shorty battery conversion, using 2200mah 105x33x24mm batteries instead. ...Will bolt straight to their conversion plate
thingiverse
If you are planning to build an interior the battery may be in the way and this tray ill tuck the battery under the hood of the Scout and be hidden by the dash once installed. THIS WILL ONLY FIT A 2S BATTERY. You will need to modify the factory...
thingiverse
Just a basic stand I made up for storage of my redcat gen 8 to take the weight of the rc off the wheels to prevent flat spots. It also works great for working on it when the wheels are off. ...Will need to print two stands, they are interchangeable from...
thingiverse
This is a low CG (center-of-gravity) shorty battery tray conversion for the Redcat Racing Gen 8 International Harvester Scout II crawler. This allows you to get the weight up front as much as possible while still keeping the lowest possible...
thingiverse
Made for the light buckets and bumpers on the Redcat Gen 8. ...Uses 2mm screws.
thingiverse
Redcat Gen 8 Beadlock (wider) Ring, aligns and works well with all 6 screws.
thingiverse
Redcat gen 8 servo relocation mount. This part eliminates most of the stock body roll and helps with bump steer. You have to move the drag link to the knuckle. See first photo Setup shown is a savox 1258 servo and an RC4WD 25T motor. Plenty of...
thingiverse
This is an optional tailgate grill/protector for the Redcat Gen 8 International Harvester Scout II scale crawler. It is meant to be secured by using silicone or glue. To make the grill sit flush with the body, most of the stock tailgate section...
thingiverse
>In keeping with the non-commercial clause of this license, if you produce this part (Gen 8 Gas Cap V1.STL) + (Gen 8 Gas Cap V2.STL) + (Gen 8 Gas Cap Base.STL) + (Gen 8 Gas Cap Spacer.STL) for others, you may not receive compensation in excess of...
thingiverse
These are door handles for the Redcat Gen 8 International Harvester Scout II scale crawler. Additional hardware needed: 2pcs: M2x8mm cap head screw To install, you will need to drill a 2mm hole through the body in the desired location. Using...
thingiverse
This is an accessory plate for the Redcat Gen 8 International Harvester Scout II scale crawler. It bolts onto the front and/or rear of the vehicle, on top of the shock tower brace. It is intended to be used to give some extra mounting surface for...
thingiverse
This is a liftgate button for the Redcat Gen 8 International Harvester Scout II scale crawler. Additional hardware needed: 1pc: M2x8mm cap head screw To install, you will need to drill a 2mm hole through the body in the desired location. We...
thingiverse
Redcat Gen 8 roof rack. Not the best but works, Used M2*8 and M2*20 hardware. The leds I used came with some Special clips that gets held in by a 15/64 hole on the light bar mount. ...Also use some countersunk screws on the lightbar to keep the roof...
thingiverse
This is an optional grill for the Redcat Gen 8 International Harvester Scout II scale crawler. It is a direct replacement for the one that comes stock with the vehicle. To install, remove the seven screws that secure the stock grill to the body.
thingiverse
This is an optional grill for the Redcat Gen 8 International Harvester Scout II scale crawler. It is a direct replacement for the one that comes stock with the vehicle. To install, remove the seven screws that secure the stock grill to the body.
thingiverse
This is an optional grill for the Redcat Gen 8 International Harvester Scout II scale crawler. It is a direct replacement for the one that comes stock with the vehicle. To install, remove the seven screws that secure the stock grill to the body.
thingiverse
These are windshield wipers for the Redcat Gen 8 International Harvester Scout II scale crawler. Note: The STL file is for 1pc. To install, you will need to drill a 2.2mm hole through the body in the desired location. The stem on the end of the...
thingiverse
This is a roof rack for the Redcat Gen 8 International Harvester Scout II scale crawler. Additional hardware needed: 4 or 8pcs: M3x8mm button head screws 4 or 8pcs: M3 lock nuts To install, you will need to drill four or eight 3mm holes (depending...
thingiverse
This is an optional grill for the Redcat Gen 8 International Harvester Scout II scale crawler. It is a direct replacement for the one that comes stock with the vehicle. To install, remove the seven screws that secure the stock grill to the body.
thingiverse
I designed these to replace the standard body mount used to mount a normal poly body onto the Gen 8 chassis. They are made to fit rare earth magnets from harbor freight https://www.harborfreight.com/10-piece-rare-earth-magnets-67488.html ...
pinshape
All three pieces bolt together, and are sized to fit the Gen 8 Scout perfectly. Just drill a few 2mm holes in your body after you chop the top and your good to go. ...Fair warning, this will take a long time to print as is, i made it so it would be both...
thingiverse
I designed these to lift up the sliders on the Redcat Gen8 Scout II. If you trim off the bottom lip under the rocker panels these allow the sliders to be tucked up nicely. These are 5mm thick, you can adjust the Z axis to make them thicker or thinner...
thingiverse
These axle servo mount is designed for the Redcat Gen 8 portal axles. The mount utilizes the stock screws and is a direct replacement for the differential cover. Gen 8 Servo Mount - Slightly offset to allow the use of the kit/stock drag link. This...
thingiverse
This is the low back rear seat to fit the redcat gen 8 axe edition. Use the 2mm socket head screws that came with the axe to assemble the seat together. ...Seat can be screwed in or double sided tape.
thingiverse
Redcat Gen 8 Front Skid Plate. Supports will be required at 1.5 layer height. Strongly recommend 80 percent or more infill for strength. I printed this in carbon fiber filament and it is very strong and solid. PLA should be fine for use as...
thingiverse
This is a rear hatch handle for the Redcat Gen 8 International Harvester Scout II scale crawler. Additional hardware needed: 1pc: M2x8mm cap head screw To install, you will need to drill a 2mm hole through the body in the desired location.