bikini modeling

These are not proper, but I didn't care for a test model. Most likely you will need to ream the holes for the motor shafts. I used a 5/64" drill and very carefully reamed the hole at a low speed. This creates a hole with a .0006" press fit. I do not...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

 I am hacking stuff together in Tinkercad, so parts of the original Voron panel retention clips and hinges were used in creating these.I plan to make matching latches in the future, but for now am using these panel...

Five basic shapes are available as elements:pieces with straight ends, adapters with either two plugs or two sockets, T-shapes, L-shapes cross-shapesTo make your own drawer partition, make a sketch like the image below, calculate...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Also download the original 'COMPLETE.BLEND' from Jumpman971's Thingiverse so you can see the model in Blender. (Also get Blender.) (I'm pushing this out before a throat piece is remodeled because I have a 2-week vacation coming up and I'm busy this...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

I think the steel should slide easily against most rigid plastics but better safe than sorry. Use Instructions: Print the model Remove the heat sink, tubes, retaining screws, and any heater or thermistor -- only the hot block and heat break should...

... with any light color and use a permanent black marker for the text. These models are not designed for dual-color printing. You'll need to print two Monster Ability Card holder v1. ...One is for the Monster cards, the other is for the shop cards.</p>

being able to reprint the broken part vs the entire model is a plus. Except for the charging ports, no glue is needed. All the STL files have been positioned to hide the seam as much as possible (when possible). The Activator Assembly parts are...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

This is an update log for an OpenSCAD model used to create keyguards for tablets. The updates are from April 22 to November 12, 2018. **UPDATE 11 Nov 2018 (version 12)** * Extended the upper end of the padding options to 100 mm. * Minor corrections...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_width = 100 use_mouse_ears = 1 pattern_element_overlap = 51 stencil_shape = 4 custom_back_camera_y_size = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

... If this is the case, and accuracy is important, you should scale up the dimensions a little bit to compensate. I only tested this for small gaskets. If the model proves unpractical for larger gaskets, contact me and I'll see how I can improve it.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 79...

Note: A Honeywell Type H filter is virtually the same size (though not tested with this model) and 3M offers a filter that claims to be compatible with both the Aer1 and Honeywell Type H. 36x rare-earth magnets, disk shape, 8 mm diameter, 3mm heigh...

(Rotate these angles accordingly if you rotate the model.) This way, you will have two layers of crossing extrusions in the spine folds. This makes for much stronger, long-lasting book hinges.</p><p>For<strong> print-on-print</strong> technique (used...

Just drag the lithophane (standing up) to the mount, and position it so that it intersects the model, while lining up the curved edges as seen in the picture. 3. While that is printing, disassemble the nightlight by pulling off the diffuser,...

I'm no design expert, and 3D modelling makes my brain hurt. However, with a lot of perseverance, a set of calipers, hundreds of edits and redesigns, dozens of test prints, I have made a replacement ring battery. You will need the following: *...

I restarted from scratch and designed this model from those other inspirations. This version allows a 5015 fan to be installed without interference to the left or right gantry positions. I placed the fan above the slightly relocated CR Touch...

Subscribe Now! A very good model from Velrock. Time-lapse print video : https://youtu.be/4lXVR1HwAAU <iframe width="560" height="315" src="https://www.youtube.com/embed/4lXVR1HwAAU" title="YouTube video player" frameborder="0"...

We successfully engineered an incredibly stable and secure mounting arrangement by adjusting the RC roof rack's structural reinforcement through computer-aided engineering models. By applying advanced design methodologies, our innovative product not...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

All nuts used are M3 squares unless otherwise stated.The +1mm fan duct is for use with longer non-standard m6 nozzlesUse the following commands to use with stock Prusa firmware: M92 E690, M500You may need to adjust the extruder motor current using...

Required Components Arduino Mega 2560 (You must use this model because you require at least 25 I/O pins) ProtoShield for Arduino Mega 2560 (Highly recommended) (Example ) 12 LEDs (I used 6 different colors) 12 Resistors with the correct resistance...

This helps with the strength of the threads as it will be printed length wise on the build placeThis gives more freedom to place pieces in any orientation, as well as add spacers between larger parts for more accents and individualityFixed stringing...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

Required hardwareRaspberry Pi Pico (RP2040) microcontroller boardUSB cable (as it has to be cut and soldered a USB 2.0 is preferred, because it only has 4 wires)4x Cherry MX key switches or other with similar size4x Keycaps (or print your own)4x M2x6...