birdhouse with camera 3d models
2802301 3d models found related to birdhouse with camera.thingiverse
Supplies: Raspberry Pi zero W (without pins) 120 Degrees camera module for RPI zero Wemos D1 mini SD Card Stepdown converter 12 to 5 volts 4 x Infrared LEDs 120 degrees 4 x Warm white LEDs 120 degrees Micro USB plug male Relay module 5 Volt Relay 3...
thingiverse
This is the improved version of: https://www.prusaprinters.org/prints/20385-birdhouse-20-with-camera-and-microphone **Download the files one by one or download the complete set on:**...
prusaprinters
This is the improved version of:https://www.prusaprinters.org/prints/20385-birdhouse-20-with-camera-and-microphoneDo you want to use a different camera? Give me the sizes then I adjust the camera plate for you.Innovations:Easy to print in PETG...
thingiverse
This is the improved version of: https://www.thingiverse.com/thing:4071301 1 x XMeye Camera Module H.264 1080P 120 degrees with microphone $ 16 on AliExpress 1 x Stepdown converter 12 to 3.3 volts 1 x ESP01S 8 x Countersunk head screws m3 x 10 1 x...
prusaprinters
This is the improved version of: https://www.thingiverse.com/thing:4071301 1 x XMeye Camera Module H.264 1080P 120 degrees with microphone $ 16 on AliExpress 1 x Stepdown converter 12 to 3.3 volts 1 x ESP01S 8 x Countersunk head screws m3 x 10 1 x...
myminifactory
Fully printable the birdhouse with spy camera. I used 2MPx Waterproof Inspection Endoscope Camera with Wifi Box from Bang good as a Spy camera. This camera can work with Android and IOS mobile device. You just need to install the APP, do wifi...
thingiverse
ESP32 Birdhouse cam ESP32 Birdhouse cam Parts list: * ESP32 cam board * Camera Module OV2640 2MP 160 degrees 850NM * Resistors * IR LED 850NM Board + Cam example I was a bit playing with some resistors and find out that for my case a 200 Ohm resistor...
thingiverse
The top cover bit was printed in transparent PLA so the LEDs could dimly shine through just to slightly light up the inside of the birdhouse enough for the camera (can be very dim). If anyone knows what the best color for Chickadees is please do let...
cults3d
... CCTV camera or even a motion camera for taking pictures of nature. No supports needed. 10% infil. Parts & instructions can be found on my website: https://www.thatrobotguy.co.uk/birdhouse-camera Support me on Patreon: www.patreon.com/thatrobotguy
thingiverse
... camera or even a motion camera for taking pictures of nature. No supports needed. 10% infil. Parts & instructions can be found on my website: https://www.thatrobotguy.co.uk/birdhouse-camera Support me on Patreon: www.patreon.com/thatrobotguy
prusaprinters
Original idea goes to JoopB1, who made this out of wood. I just used their measurements (found in the attached PDF) and turned it into an STL model to be made out of PLA (for outdoor use I would recommend PETG).</p><p>I printed mine at 50% because...
thingiverse
... designed to print with as little supports as possible print the roof stood on its end requires no supports then just glue together Link to camera used : https://www.amazon.co.uk/gp/product/B074389PMT/ref=ppx_yo_dt_b_asin_title_o00_s01?ie=UTF8&psc=1
myminifactory
... designed to print with as little supports as possible print the roof stood on its end requires no supports then just glue together Link to camera used : https://www.amazon.co.uk/gp/product/B074389PMT/ref=ppx_yo_dt_b_asin_title_o00_s01?ie=UTF8&psc=1
cults3d
designed to print with as little supports as possible print the roof stood on its end requires no supports then just glue together Link to camera used : https://www.amazon.co.uk/gp/product/B074389PMT/ref=ppx_yo_dt_b_asin_title_o00_s01?ie=UTF8&psc=1...
thingiverse
It is important for bird keepers to check the chicks from time to time. ...This birdhouse with sliding top lid makes this possible.
thingiverse
This is a simple birdhouse with a perch. Insert a wire through the bottom of the door for the hinge. ... Slide a roofing nail through the hole in the roof to hold the door closed.
thingiverse
This birdhouse has a hole of 32mm. Can be fast connected to a pole with two ty-raps. Instructions This version is made of al little more than 222 grams of PLA. ...Takes 24H to print
thingiverse
Simple Birdhouse with nameplate STEP files included to add text to nameplate. I scaled this model in Cura to 75% to fit the Ender 3 build volume. ... No supports needed.
thingiverse
A round birdhouse with a sloped roof and a perch. There's a mounting bracket on the back with two screw holes and a loop on the top so you can hang it. It should print fine without any support material. You can use infill if you want to reinforce...
thingiverse
... wooden screws. Optionally it does have third part, which is tree mount which allows easy mount on the trees with the cable ties. It does need 2x M4/M5 screw and nut. It is designed for rather smaller birds, like Tit and/or House sparrow. ...
prusaprinters
A round birdhouse with a sloped roof and a perch. There's a mounting bracket on the back with two screw holes and a loop on the top so you can hang it. It should print fine without any support material. ...You can use infill if you want to reinforce the...
myminifactory
This is a circular birdhouse with a slanted roof and a perch. I designed it so that it would use little material, and print without supports. The entrance hole diameter is 40mm, and the interior is 110mm in diameter. You could scale it to your...
thingiverse
The second mounting hole is a standard recessed hole that can be accessed through the "doorway" in the front of the birdhouse with a long screwdriver. In case you don't want to make holes in your tree, there are also four holes along the back of the...
thingiverse
Give the birds a nice plant to live under! ...The top of the bird house has a nice planter, complete with a rear water drain.
thingiverse
(Shown here at 75% in wood filament) I rebuilt the base of the antlers so that they could be attached with the included pin and had to print with lots of support, but I like the result. ... Instructions...
thingiverse
I think I pushed Tinkercad pretty close to it's limit with this one - it was quite slow to work with in the end, and it took about 10 attempts to download the stl without getting hit by a "bad gateway" error :-) Print Settings Printer: Zortrax M200...