blackcat modeling

Really like the wheel from TheSloppyApprentice's Watermill and was looking for ways to hold it besides that large frame in the source.So I could make it stand in a bassin or hang under some opening where water is dropping off.So here are 2...

A very good model from Velrock. Yet another remix pose Time-lapse print video : https://youtu.be/xsk3FDa-Cx8 Baby Yoda : https://www.thingiverse.com/make:872409 <iframe width="560" height="315"...

Note that the Shapeways model has been modified to meet their minimum wall thickness requirement, so looks a little different; it uses the same idea. You'll need to order two if you get it from Shapeways, since it's only half the puzzle. On the plus...

(I included a simple cube STL file because Thingiverse requires at least one 3D model per Thing.)   Using Files are offered for three different levelling sheet thicknesses: 0.10, 0.15, and 0.20 mm. Ideally, you should use the files with the number...

... The COMPLETE Sunken Kingdoms I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Tritons are the proud folk of the seas, which ancestors are common to those of the Alfar.

Finally, if your printer's bed is larger than mine and can accommodate the full required width of the inserts, you can merge the included additional bodies Body30, Body67, Body68, and Body69 with the corresponding model parts. The weight of each...

Finally you should set up channel mixing for tracked models in your transmitter. I added 2 photos of my mixer setup, but this video here explains it very well: https://tinyurl.com/bdns4pj5 It took me half an hour of trial&error negating channels...

twisting both wire pairs reduces possible crosstalk and possible issues from it.&nbsp;there are holes for zipties after each dragchain, use it to secure the wires but leave some wiggle room for the wires inside the dragchain, if they are to tight...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp How to create your clamp & accessoriesSelect the clamp size relevant to the...

*** UPDATE 30/06/2021 *** As lots of people have noticed, the original model is a ridiculous reducer at a ratio of about 3:1 from the original duct. I've now added a design that is much larger (labelled as "Full Size") and can be printed in three...

Eye diameter - These three dimensions make up the foundation of this model's unique structure, resulting in eyes that stand out at an impressive six units large. Layer height - Perfect for intricate designs or subtle layering, with a precise setting...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_top_outer_edge_chamfer_radius = .6 stencil_vertical_position = 50 use_mouse_ears = 0 custom_back_camera_x_size = 20...

What's IncludedThe entire Anvil Digital Forge Patreon release for January 2024, including; Multi-Shell Options:A number of STLs are labled with "(Multi Shell)" - these files can be imported into Blender (reccomended), or Meshmixer, or various other...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Although the chinese version is much cheaper, be warned that some models lack the reverse polarity protection feature from the original, even if they claim otherwise on the backside. Also, some clones have a different layout with non-centered power...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

Use "leveling_test.stl" model to test auto-level accuracy. I made some work tests of this firmware but there still could be bugs there, so use it on your own risk. Enjoy! :) Update 1: My Start and End G-codes in Cura working well with this...

That said, i fixed anything on this model, and it is very much printable as is, you just may have to add holes for your hardware manually, or take the f3d-file and redesign it to your liking. Happy printing! A few days ago i stumbled upon the "The...

Signal dimensions are taken from the book Model Railway by B.V.Barkovskov et. al. Published - Moscow 1989 - ISBN 5-277-00181-6 p78-79. Additional documents with dimensions were found at the Russian scaletrainsclub.com forum. A very comprehensive...

... diameter of the hose end 30mm away from the tip (the wider part) This will give me the diameter and taper needed to revolve a new part for anyone who wants one. Please let me know what make/model it goes to and I'll add it if I am able. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

Note: The X axis part is for the current model of the Geeetech I3 Pro printer that uses a metal plate on the X axis to support the linear bearings and extruder holder. When I was assembling my Geeetech I3 Pro C printer, I was struck by the fact...

I created this VW Passat B8 phone tray because my iPhone 8 with cover didn't fit into the standard one. Rotating the USB port by 90° it has space for phones with a length of up to about 15 cm which is about 11mm more than the standard tray offers....

Click the “like” button and show your support. If you find this model useful, feel free to buy me a coffee. Here's my attempt at replicating the Infinity Orb from the film Guardians of the Galaxy.In one of the pictures, you can see a side by side...