blimp 3d model

* The Cura version used for this print of mine is version 4.10.0 Printer model: Ender 3 V2 Filament: eSun PLA+ Filament Color: Fire Engine Red Layer Height: 0.2mm Initial Layer Height: 0.2mm Line Width: 0.4mm Wall Thickness: 0.8mm (Light use) OR Wall...

I have since printed out another model in ABS which I am hoping will be more durable. PETG would be another more durable substrate to consider using. Special thanks to Jim Harmon at Keystone College and Emmitt Zugar at Salem Community College for...

This is a multimaterial model. I don't have a multi material printer but learned that you can create a multi material print pretty easily without special hardware (as long as the multi material part does not span over to may layers - otherwise it...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

Anser from Niklas: Hi Bas, take a look at Stefan’s video about filament drying, I learned a lot: https://www.youtube.com/watch?v=eqQRN9TUw08 You do need an active dryer, not just desiccant, but your Esun dryer might work (don’t know the model). Were...

DO NOT LOOK AT THE SUN WITH THIS!Also have a look at my improved Dobsonian Design:https://www.printables.com/model/317112-propdob-telescope-foldable-travel-dobsonian-45-mir Hi, this is a Newtonian telescope with a 114 mm diameter mirror and...

This model is cheaper than the usb c version and charges the Oculus Quest perfectly. This greatly improves your playing time and you could even charge the battery while using it. One design came close to what I liked, but was made for a different...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

... The COMPLETE Sunken Kingdoms I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Tritons are the proud folk of the seas, which ancestors are common to those of the Alfar.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

If you need to use a different pump you can model and print your own adapter as it is just a rectangle block with a hole for the pump water outlet. The inlet block should be 80mm tall and 32mm wide minus half a millimeter for fit tolerance. If you...

The extruders are mounted using the same procedure.Made with Onshape:Source CAD: Snapmaker Artisan Modular Side ShelvingPrint Recommendations:Print in PETG for the increased strength.Rotate the models so they are laying down, bosses facing up.Print...

Helicopter Collective Controller Work in progress. 6/17/20 Added File Added collective_open v4.f3d (An assembled model of all the parts.) You can alternatively use my Russian style grip located here:...

They can easily be swapped around.PrintingMain HandleIn general you should use the flattest side of the model on the print bed. Your settings shouldn't be adjusted too much, the standard high quality settings of your printer (or whatever tuning works...

Also, my printed model needs some clean-up on the outer edges of the ducts (which you can see I did not do). You may have better results with your printer. Printing & Assembly notes: Save the 2 self-tapping case screws when you disassemble the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 11 custom_back_extra_port_corner_resolution = 8 custom_bottom_fillet_radius = 1.6 custom_left_port_corner_resolution = 8...

Model of the pusher cap and the skirt part used on an On/Off switch combination cast aluminum IP40 case The case with two momentary switches made more than 40 years ago in the GDR (do not call it East Germany, please) works still perfectly fine. It...

I design a Electronic Bay Cover with LED Light Just a little favour>>>Less then 10% of downloaded Models get a like.→ If you like the design, it will be nice if you click on the like button and maybe share your print.   Its a heavy redesign of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

It's also compatible with the Chinese clones of both these models, often referred to as "J-head" extruders. There is a cable guide built into the design which will assist with keeping everything tidy and reduce any stress on the heater and thermistor...

This set may fit other models. I can't make guarantees on fitment.\nAnyone familiar with the Makerbot series printers will know that it's quite dark in the build space. They provide you with a roving white LED, and a red AMBIANCE LED which is both...

Videos of it in Action https://youtu.be/r5L5heNE0SIhttps://youtu.be/OzILwtWoT2M What Else Some other great models to add https://www.thingiverse.com/thing:3090510 BMG bowden mount for 3030 extrusions Updates 2020 Jan 22 * Better fit for fan magnets...

The model shown has six in each ring for a total of twelve. Print one of each of the remaining files. Carefully remove any burrs or imperfections in the print especially on surfaces that move against one another. The “Spinning Terrain” prints...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame which require support. You may need to use a raft or brim to secure the part...

Please feel free to build on what I've produced, maybe tweak things to find a home for the hero boards or a model of the Batmobile. I'm going to keep my Hot Wheels Batmobile with the hero boards in the Arkham Asylum box. ... ## [CLICK HERE TO...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

Subsequently, Bondtech integrated this improvement into their model.This is what you need:Gears, bearings, and screws set (you can take yours from your BMG extruder)                 ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...