block and tackle calculator 3d models
2313294 3d models found related to block and tackle calculator.thingiverse
Simple 3 to 1 block and tackle. ... #8-32 x 1-3/4 in Machine Screws used
thingiverse
A lighter easier to print complete re-engineering of the MOKO block and tackle https://www.thingiverse.com/thing:153197 Thank you for the inspiration MOKO. Same great pulley, but much lighter, just as strong, and with a through hole to help with...
thingiverse
Simple block and tackle-model for lightweight items. Designed for a 4mm rope You need: Hex- or allenscrews M5x35 (2pc.) M5x55 (1pc.) M5x70 (1pc.) Self-tighten nuts M5 (4pc.) Washers for M5 (8pc.) Carabiner 5mm (2pc.) DO NOT USE IT FOR HEAVY WEIGHTS!
thingiverse
With these you can make: 2 x advantage: Gun tackle 3 x advantage: Luff tackle 4 x advantage: Double tackle I've succesfully tested a Luff tackle with a load reduction from 15 to 5 kg To reproduce my setup you'll need one dual and one single sheave...
thingiverse
This is a block and tackle pulley system for use with 5mm paracord (I am sure other sizes could work too) It requires two M5 carriage bolts >35mm, two m5 nuts and two small washers to fit between the nut and the printed block. A large washer inside...
thingiverse
I made the Block and Tackle - Pulleys by SteveWall with two variations -- instead of using wooden dowels, I made a second pulleyplate adding the "dowels" to it, making a male/female assembly. I also used a single 3mm x 22 cap screw in the center to...
cults3d
I needed a block and tackle to lift hay bales in my shed. I found this one here by Mysabre73: http://www.thingiverse.com/thing:963214 but it was too big for my 150x150 Printrbot Simple. I got it printed at 90% but figured I'd rather have 608 bearings...
thingiverse
I needed a block and tackle to lift hay bales in my shed. I found this one here by Mysabre73: http://www.thingiverse.com/thing:963214 but it was too big for my 150x150 Printrbot Simple. I got it printed at 90% but figured I'd rather have 608...
thingiverse
This project began when my son chose to investigate block and tackle for his 1st grade science fair project. I was going to zip down to the local Home Depot and buy the supplies, but then thought, “I should just print em!â€. I iterated the...
thingiverse
With the provided files, different tackles can be created (1:1, 1:2, 1:3, 1:4 [and 1:5, if you're pulling upwards]). For other configurations edit the scad files. For each workpiece you need two strips: 1st with recesses for the nuts...
thingiverse
3D image of an old block and tackle sash brake no longer in production as the company no longer exists
thingiverse
this is a block and tackle i designed so that i could lift things easily around my shop. I printed the parts that will be handling the main part of the load at 100 percent infill. Everything else was printed at 50% honeycomb infill. For the complete...
thingiverse
I printed the sheaves and spacers in one print and then the block plates in groups of two Shouldn't need any supports, just pay attention to the bearing retaining flange and face it upwards. The knot used on the first sheave is a hangmans knot. ...
cgtrader
Block and tackle. Available in collada and obj. Others on request. 1 single mesh with 1 single texture. ...
myminifactory
Just for fun I designed a block and tackle with the intention of seeing if I could make one strong enough to hold my own weight with paracord. (Paracord as seen on Amazon: http://amzn.to/1gIiqlo) This design used 6 pulleys to divide my 170 lb body...
pinshape
Just for fun I designed a block and tackle with the intention of seeing if I could make one strong enough to old my own weight with paracord. (Paracord as seen on Amazon: http://amzn.to/1gIiqlo) This design used 6 pulleys to divide my 170 lb body...
thingiverse
Just for fun I designed a block and tackle with the intention of seeing if I could make one strong enough to old my own weight with paracord. This design used 6 pulleys to divide my 170 lb body weight 6 times into roughly 30 lbs input force. It...
thingiverse
This is a small, low cost, block and tackle that was created to demonstrate their use. ... It's intended to be used with smaller diameter paracord, and is held together with a M2x12 socket head cap screw (no tap required to install, just thread in).
thingiverse
This is a set of Block and Tackle pulleys that were made for Andromeda One's Virtual Summer STEM Program. The STEM video that goes along with these models will be posted here once it goes public on YouTube. In addition to the 3D printed part you...
thingiverse
This double block and tackle pulley has been designed for classroom demonstration and experimentation. I printed with a layer height of 0.12 mm but you could go higher. I printed with a wall thickness of 1.2 mm and an infill of 20% Baseplate...
thingiverse
Block and tackle hardware for a wall shelf. These look great but are mostly just for show. I wouldn't trust them to hold a significant amount of weight. I have brackets underneath of this huge shelf because it weighs around 100 pounds. I used a 1/4...
thingiverse
Instructions Build one each of the outsides (I called one the block and the other the tackle, but I'm not sure if I'm right about those names.) Build five of the new-sheaves, one new-sheave-sm and one new-sheave-stop and two of the new-hook. ...I used...
thingiverse
... ...Thanks to them for their hard work and research! Instructions Print this plate and assemble with M3 bolts. I needed to drill out the holes in mine and sand some of the parts down so they would roll smoothly. ...I also printed mine at 100% infill.
pinshape
Summaryexperiment to test the bearing after 1.5h of cleaning with a sharpened screwdriver... ...the bearing runs very smooth and its own weight momentum makes it rotate about 8 times after i stop turning it.
thingiverse
experiment to test the bearing after 1.5h of cleaning with a sharpened screwdriver... ...the bearing runs very smooth and its own weight momentum makes it rotate about 8 times after i stop turning it.
thingiverse
Customized version of http://www.thingiverse.com/thing:148571 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=148571 Instructions Using the following options: bevel =...
thingiverse
Customized version of http://www.thingiverse.com/thing:148571 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=148571 Instructions Using the following options: f = 0.1...