blue robotics 3d models
81249 3d models found related to blue robotics.grabcad
This is the Blue Robotics SwitchBlox, a collaboration between BlueRobotics and BotBlox
thingiverse
These are the blue robotics m100 thrusters from https://www.bluerobotics.com/store/thrusters/m100-p-propeller-rev-r1/
pinshape
This is a reworking of the excellent Blue Robotics T100 underwater ROV Thruster. ...These parts have been adapted to utilize the cheap (~$5) A2212/13T 1000KV Brushless Motor, enabling the construction of a cheap, but efficient, thruster for your ROV.
thingiverse
This part is for mounting a [Blue Robotics low-light USB camera](https://bluerobotics.com/store/electronics/cam-usb-low-light-r1/) in a [FitStill Dive Housing Case for GoPro Hero 5...
prusaprinters
The 1_0_b file has the motor holes for straight mount, the 1_0_a file has the angle mount holes. Print instructionsCategory: Robotics Summary The Blue Robotics T-100 and T-200 ROV thrusters (http://www.bluerobotics.com/) are brilliant, but they...
thingiverse
The Blue Robotics T-100 and T-200 ROV thrusters (http://www.bluerobotics.com/) are brilliant, but they suffer from one major issue. The mounts they come with are not strong enough to ensure that the thruster does not separate from the vehicle. After...
thingiverse
As it happens, Blue Robotics publish the CAD models for their thrusters, so I decided to modify them for my cheap motors. More information can be found here: https://hackaday.io/project/18036-cheap-rov-thruster Print Settings Printer: ...
thingiverse
An electronics mounting tray for use with Blue Robotics 3" acrylic enclosure and end caps. Designed for laser cutting from 3mm ABS or similar. The tray is intended to be cut to custom lengths, so there are perforations every 20mm that outline the...
thingiverse
Home made robot for no particular reason. ...Best if hollowed in your software.
thingiverse
Adapts a [Blue Robotics Low Light USB Camera](https://www.bluerobotics.com/store/electronics/cam-usb-low-light-r1/) to an [Impact Imagery GoPro Hero 5 Session Dive...
thingiverse
This project contains a set of 3d printable main side frames and lower frame for a BLue Robotics Bluerov 2 Remote underwater Vehicle https://www.bluerobotics.com/store/rov/bluerov2/ At the time I created these STL copies of the real frame you were...
thingiverse
This Edition of my reinforced ROV mount for the Blue Robotics T100 and T200 thruster was created for use with 4" diameter pipe hulls, as seen on the SV Seeker ROV. You'll want to print it flat side down. As always, Design files are available as...
prusaprinters
the 3d printed frames in ABS are buoyant anyways, so you may find you need to add more weight than stock. For assembly of the ROV, other components and instructions, check out the blue robotics store. It is in my opinion the most accessible "pro"...
prusaprinters
You'll want to print it flat side down. As always, Design files are available as well, just let me know what format you need Print instructionsUnassociated tags: SV Seeker Category: Robotics Summary This Edition of my reinforced ROV mount for the...
prusaprinters
It is intended for use in areas where there is a high amount of seaweed or other debris that could foul the thruster, and the lower thrust is offset by the greater protection. Print instructionsUnassociated tags: blue robotics Category: Robotics...
thingiverse
It seems Blue Robotics have changed their thruster design since piercet's original intake grill was designed (or it was actually only good for the T100?) - the motor now sticks out about 13mm on the front, leaving a gap when using the intake grill. ...
thingiverse
This is a mold for terminating Blue Robotics tether (4mm slim shown, but standard 7.6mm file is also included) onto an RMG-2-FS cable so that the tether may be easily disconnected from the ROV. Should be able to get the QD swap done for around $150.
thingiverse
This is a weed guard for use with Blue Robotics T100 and T200 thrusters. The front unit mounts under the stock nosecone. You will need two 10mm M3 stainless cap head bolts to mount this, the stock bolts are not long enough. The rear guard mounts to...
grabcad
The Fathom Spool is a rugged and easy to use tether spool for the Fathom and Fathom Slim ROV tethers. An integrated slip ring provides connections for up to eight tether wires, even while the spool is rotating. It’s quick to set up and use in a...
grabcad
The Fathom Spool is a rugged and easy to use tether spool for the Fathom and Fathom Slim ROV tethers. An integrated slip ring provides connections for up to eight tether wires, even while the spool is rotating. It’s quick to set up and use in a...
cgtrader
Blue Robot 3d model. Included formats: 3ds max 2017 + Vray, 3ds max 2017 + Corona Render, Blender 2.8 + Eevee or Cycles, .FBX, .OBJ. Also included 2 archives: PBR_maps for PBR shading, and nonPBR_maps for 3ds max and Corona Render and Vray. All...
thingiverse
On my ROV build I needed to add straps to hold the tubes together and to hold them to the frame of the ROV. The original plates that were attached to the flanges were custom laser cut, but the team wanted to switch to the BlueRobotics domes, which...
thingiverse
Designed these stands to raise the 4 inch enclosure about 2 inches off the bottom of the frame of our custom ROV. Use a layer of foam (in our case cut pieces of a thin foam mat) to line the inside to get a tight fit. ...One side will need a hinge and...
grabcad
6 DOF robotic arm that usually use in manufacturing industry commonly on automotive firm.