boost models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

This is a set of models, minus one piece noted in the instructions, for a minimal cutting body modification kit for the Adventure Force Commandfire by Dart Zone. Print instructionsForward I am not the most advanced 3d printer user. I printed these...

They can easily be swapped around.PrintingMain HandleIn general you should use the flattest side of the model on the print bed. Your settings shouldn't be adjusted too much, the standard high quality settings of your printer (or whatever tuning works...

It was hard to get some screws in it so I had to manually remove parts that model has removed for you. Make sure if you use screws to hold bearings tight, lowest ones have low-profile heads or they will be lower than extruder nozzles and hit your...

It works alright as it is but it does bounce around sometimes (most notable as read below; CONS). TL;DR PROS- Works with common SN04 leveling sensor Sensor range covers the entire area of the hot bed. Fine tunable height adjustment by turning an M3...

I also adjusted the tolerances of the nozzle wrench brackets so that they fit a bit tighter.I also felt the cover did not latch securely enough, so I also deepened the magnet pockets on the case, so you can stack two 6x3mm magnets in each pocket.I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

Step 7: Slice the model and place the sliced Gcode in the same folder that Markpen.exe exists. Launch the program, and it will generate the _Output.Gcode and open the preview. Step 8: Turn on the 3D printer and start printing happily. Note:...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

If you are looking for more, check out our premium projects: https://codeandmake.com/premium OpenSCAD Customizer Options You can customize everything from the size of your cards, to the number of decks it will hold and you can even create a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 0 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

WORK IN PROGRESS Modeled off of reference pictures, many dimensions are guesses. This is intended to be a NON-Firing, but bolt operable, replica. can be printed entirely in PLA (if possible, the charging handle and magazine spring is better...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

I have completed assembly and everything works so this addresses some of my main wants for this awesome model. I am also going to include the full parts kit here (the originals I used also), so everything you need is in this one thing saving any...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

(Rotate these angles accordingly if you rotate the model.) This way, you will have two layers of crossing extrusions in the spine folds. This makes for much stronger, long-lasting book hinges.</p><p>For<strong> print-on-print</strong> technique (used...

unless you have a special edition like a Porsche, Mercedes, or older Audi, VW, or BMW model, which is what I have. For most of these special editions, the original push bar won't fit. I found a design on Thingiverse called *Klein-laui* and tested...

Tools Hex wrench 2mm and Mmm...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale]   Among the first risen humans in Draksborne, Violet thought herself to be insane for her first life upon Tharador. For when she woke she remembered all that had...

No idea why it defaults to NEGATIVE: MODEL SETTINGS: Max Size: 100(mm) Thickness: 4mm Boarder: 2mm Thinnest Layer: 0.6mm Vectors Per Pixel: 6 Base/Stand Depth: 0 Curve: 0 I then print the lithophanes in ABS at: 0.15 layer thickness (first layer 0.2)...

Enjoy :) Update 04-05-2021: Adding ender 6 models, upgrading all to V4.3 (slotted mount holes for 2mm height adjustability) and adding "fan duct up V2" which has integrated grill. It's more tricky to print because of the small features so i'll leave...

If your adapter feels loose on the mask, try the "generic" version - it is meant to fit masks that have a looser adapter/thinner gasket than the original 3M ones. UPDATE 05-04-2020: v4 introduces model markings on the adapter - based on the feedback...

So far my failures are in optimizing the printer tuning to keep the model airtight. As stated in the Harvard paper, they printed a form and molded silicone for the soft actuators. I probably should do that too, but I am determined to work with FDM...

My prototype box had a problem in which the combination could be guessed by feel due to the slack in the model. This problem was fixed with a number of features that make guessing the combination by feel very difficult. As an additional precaution, I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 0 custom_top_port_corner_resolution = 8...

The overhangs should be ok for 90% of printers out there. Description =========== The drybox itself is a Snapware 40 cup/9.5L storage container. I consider it on the more costly side (~20 USD) but it was hard to find a container that fit all the...

... Use your best judgement if you have more experience at printing. This is my first upload, I am still struggling with FreeCad. Hence, the models might not be the greatest so please be kind. Use at your own risk but they work on my printer! ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

... - The +1mm fan duct is for use with longer non-standard m6 nozzles - Use the following commands to use with stock Prusa firmware: M92 E690, M500 - You may need to adjust the extruder motor current using M907 but that depends on your motor model